Not many publications are available on using microsimulation models to analyze the feasibility of implementing the dynamic bus lane (DBL) concept. The paper presents the methodology and calibration process used for DBL modeling. For the selected four sites in Rzeszów (Poland), three options were analyzed: no bus lane, standard exclusive bus lane (XBL), and dynamic bus lane. The analyses were carried out using PTV Vissim software with an additional logic script to control the DBL activation. Simulation model parameters were calibrated using a genetic algorithm. The final assessment of individual options was based on the weighted average travel time for all transport modes. The results show that the dynamic bus lane could bring the same benefits to public transport and cause only a slight increase in travel times in private transport compared to XBL. The XBL solution, depending on the site, led to increasing the average travel time in private transport by 12% to 25%, while the dynamic bus lane increased by 1% to 12%. Weighted average travel time per person is proposed as the overall indicator of efficiency. Preliminary analyses show that the bus volume, bus occupancy, routing, and traffic conditions will affect the efficiency of the new solution.
The application of various modifiers has emerged in recent years to improve conventional petroleum-based bitumen properties. The natural asphalt called Trinidad Lake Asphalt (TLA) has been applied very often due to its consistent properties, high viscosity and density, and superior rheological properties, and effective blending with other bitumen. However, most studies on TLA-modified binders always focused on physical and rheological properties in the original (unaged) condition, but the details about aging properties are often neglected. This study aimed to investigate the effect of short-term aging on the physical and rheological characteristics of the 35/50 base bitumen modified by the addition of two different TLA contents. The conventional physical tests and dynamic shear rheological tests were undertaken before and after aging to measure the penetration and softening point, complex shear modulus, and phase angle of the modified binders, as well as to calculate the zero shear viscosity using the Cross model fitting procedure. Based on the results of the above-mentioned comprehensive testing, the effect of aging on TLA-modified binder properties was evaluated using aging indices, as well as a direct comparison of results. The tests revealed that the short-term aging of TLA-modified binders did not worsen or reduce the pavement resistance to permanent deformation or the load-bearing capacity of the asphalt mixture.
Mastic asphalt (MA) has been recognized as one of the most deformation-resistant and thus durable materials for bridge pavement. The performance properties of MA are highly dependent on the physical and rheological properties of the binder applied in the MA mixture. To modify the binder properties to obtain the expected performance of the MA mixture, Trinidad Lake Asphalt (TLA) is often applied. In this study, the TLA-modified binders to be used in mastic asphalt bridge pavement systems were evaluated to develop the optimum material combination using conventional and performance-related testing. Physical and rheological tests were carried out on TLA-modified binders with the different modifier content in the range of 10–50% on a weight basis. The tests revealed that the TLA modifier addition to the 35/50 base bitumen should be close to the value of 20%. Higher concentrations of TLA may make the binder very stiff and could induce low-temperature cracks in mastic asphalt.
Mastic asphalt (MA) has been particularly popular in recent years for bridge pavements due to many advantages such as easy application, good waterproofing properties, and high durability. However, the drawback of mastic asphalt in comparison to other asphalt mixtures is its lower resistance to permanent deformation. Trinidad Lake Asphalt (TLA) is often applied to make mastic asphalt resistant to permanent deformation. Practical experience demonstrates that serious failures may occur if MA pavement design and materials selection is not taken into account sufficiently. Therefore in this study, the influence of two parameters: zero shear viscosity (ZSV) of TLA-modified binder and mastic composition described by the filler–binder ratio, on the permanent deformation resistance of the MA mixture was evaluated. The primary purpose of determining the ZSV of the TLA-modified binders was to evaluate the rutting potential of the binders. The permanent deformation (rutting) resistance of the MA mixtures was evaluated based on static and dynamic indentation tests. The optimum content of TLA in the base bitumen and the optimum filler–binder ratio in the MA mixture were obtained based on multiple performance evaluations for modified binder, mastic and MA mixtures, i.e., 20% and 4.0, respectively.
This paper presents the properties of an SMA LA (stone matrix asphalt Lärmarmer) mixture based on the polymer-modified binder PMB 45/80-55, formed by the addition of zeolites (synthetic zeolite type Na-P1 and natural zeolite—clinoptilolite). The compositions of the SMA 11, SMA 8 LA and SMA 11 LA mixtures based on modified bitumen with PMB 45/80-55 (reference mixture) or PMB 45/80-55 with Na-P1 or clinoptilolite were determined. Their resistance to permanent deformation, water sensitivity, water permeability and susceptibility to changes in texture and skid resistance during the period of use were verified. Adding zeolites reduced the production temperature by as much as 15 °C for the SMA 11 LA mixtures and 20 °C for SMA 8 LA. The addition of zeolites did not significantly affect the resistance to permanent deformation, the water permeability or the mass loss. The mixtures with clinoptilolite were resistant to the harmful effects of water, while the mixtures with Na-P1 proved more sensitive to water. Water permeability tests showed a higher permeability for SMA 11 LA compared to SMA 8 LA due to the higher nominal aggregate size. The Cantabro test showed greater particle loss for SMA 11 LA than for SMA 8 LA. A skid resistance and macrotexture analysis indicated that the SMA LA layers required special maintenance on the road due to the clogging of pores in the mix structure.
The use of mineral waste for the production of lightweight artificial aggregate is an important element of activities for sustainable development in construction and the implementation of the objectives of the circular economy. The article presents the physical, mechanical, and ecological properties of an innovative artificial aggregate produced from bottom sediments, concrete dust, and municipal solid waste incineration fly ash. The obtained research results confirm that the developed material achieves technological properties comparable to artificial aggregates available on the market, both commercial and those derived from recycling. However, the increased leachability of chlorides and sulphates remains a significant challenge, which may limit the scope of its applications. Despite this, the material shows the potential for use, among others, in the production of lightweight concrete. The analyses carried out have shown that the thermal hardening processes (200–400 °C) and autoclaving do not guarantee full immobilization of harmful substances contained in the raw materials for the production of this type of aggregate.