This study investigates cavitation in a rectangular-profile Venturi tube using numerical simulations and four turbulence models. The unsteady Reynolds-averaged Navier–Stokes technique is employed to simulate vapor cloud formation and compared against experimental data. κ-ε realizable, κ-ε RNG, κ-ω SST, and κ-ω GEKO models are evaluated. The simulation results are analyzed for pressure, turbulence, and vapor cloud formation. Discrepancies in cavitation cloud formation among turbulence models are attributed to turbulence and vapor cloud interactions. RNG and SST models exhibit closer alignment with the experimental data, with RNG showing a superior performance. Key findings include significant vapor cloud shape differences across turbulence models. The RNG model best predicts velocity at the throat exit with an error of 4.145%. Static pressure predictions include an error of 4.47%. The vapor cloud length predictions show variation among models, with the RNG model having a 0.386% error for the minimum length and 4.9845% for the maximum length. The SST model exhibits 4.907% and 13.33% errors for minimum and maximum lengths, respectively. Analysis of the cavitation number reveals agreement with the experimental data and sensitivity to cavitation onset. Different turbulence models yield diverse cloud shapes and detachment points. Weber number contours illustrate the variation in the cavitation cloud behavior under different turbulence models.
A computationally-supported experimental technique is presented, to measure height of luminous flames, using convolution and density-based spatial clustering for image processing. The experimental setup employs a high-definition camera array to capture flame imagery from 0°, 45° and 90° visualization planes. The volumetric fuel flow was ranged from 350 to 1800 cc min −1 and images of the resulting flame structure were captured and measured. Results show that output measurements are affected by both the volumetric fuel flow and the visualization plane. Whilst the former is evidently the most significant factor, the latter was found to be relevant, since several flame features, particularly, flame tilt and flickering, are only perceivable through specific visualization planes; attributed to uneven flame structure due non-homogeneous thermal stress. The experimental technique proposed yields an overall statistical tolerance of 1.29 cm and an expanded uncertainty of 0.609 cm (∼11.5%). From these results, the test is considered successful and the proposed experimental technique is deemed to be on par with the already existing ones. The utilization of spatial density clustering of image gridded data has only been tested for this implementation; being severely constrained by the sample size and density variability of the data. Consequently, care should be exercised. Nonetheless, this approach was found to inherently recognize flame front edge, and mitigate variations of pixel value due change in flame intensity, normalizing image processing, hence, it is proposed as a viable alternative for flame feature/structure visualization and estimation, and further research is encouraged.
The work aims to numerically evaluate different injection configurations for the analysis of a two-phase flow behavior and evolution through a staggered Y-junction pipeline. To minimize agglomeration between inlets, the injection zones have a separation distance, avoiding areas with eddies or swirls owing to strong turbulence. Six input scenarios were examined accordingly with injection system experimental data. Results show significant variations because the main fluid develops a swirl over the pipe center. This is generated immediately after the phases’ supply zone due to the oil-phase because it presents a partial pipe flooding, even in the water injection zone. Moreover, the supply configuration has significant relevance to the main flow development. Accordingly, many flow patterns can be achieved depending on the phases’ confluence coming from the supply system. The interface velocities confirm the transition process and flow pattern development, which are driven by the phases’ velocities describing the early stages of three flow patterns formed during the fluids’ confluence. Finally, a substantial extent of the conjunction process points out that caution must be exercised during the injection supply system selection for this type of junction pipeline to achieve a better, and smooth blend, with either narrow, medium, or wide emulsions.
This work aims to analyse different injection configurations for the analysis of the emulsification process in a Y-junction staggered horizontal pipeline. The case study comprises a multiphase analysis between two liquids, one with high and the other with low viscosity. Through numerical simulations, it is intended to explain the behaviour and describe the mechanism that produces the water–glycerol emulsification process with three supply zones for both fluids. According to the phase injection scheme, six input scenarios or combinations were analysed. Through strain rate and shear velocity analyses, it was possible to describe the early stages of the emulsification process before a flow pattern is constituted. The results show significant variations concerning the high viscosity fluid, mainly because it presents a partial pipe flooding, even in the injection zone of the low viscosity fluid. The fluid ratio varies according to the input position of the phases. Additionally, a smooth blending process was observed in some scenarios, due to the fact that the continuous phase gradually directs the main fluid to the pipeline centre. The analysis revealed that supply configuration has a significant relevance on the development of the main fluid flow and a substantial extent on the emulsification process.
This study presents a comprehensive assessment of the hydrodynamic performance of a novel pipe network with tessellated geometry and allometric scales. Numerical simulations were used to evaluate flow behaviour and pressure drop. The comparison geometry featured a Parallel Pipe Pattern (PPP), while the proposed design employed a Rhombic Tessellation Pattern (RTP). Steady-state simulations were conducted under identical boundary conditions, examining water mass flows ranging from 0.01 to 0.06 kg/s. The results revealed RTP significant advantages over the PPP. The RTP, integrated with a fractal tree pattern, demonstrated remarkable capabilities in achieving uniform flow distribution and maintaining laminar flow regimes across the mass flow rates. Additionally, exhibited an average reduction in pressure drop of 92% resulting in improved efficiency. The Reynolds number at PPP inlet was 5.4 times higher than in the RTP, explaining the considerably higher pressure drop. At a mass flow rate of 0.06 kg/s, the PPP experienced a pressure drop of up to 3.43 kPa, while the RTP’s pressure drop was only 0.350 kPa, highlighting a remarkable decrease of 91.5%. These findings underscore the RTP superior performance in minimizing pressure drop, making it suitable for accommodating higher mass flow rates, thus highlighting its exceptional engineering potential.