Marcin Paprocki

Dr. Marcin Paprocki

Institute of Engineering and Technology, Faculty of Physics, Astronomy and Informatics, Nicolaus Copernicus University in Torun, POLAND
orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 July 2012 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
Krystian ErwińskiKrystian Erwiński
Krystian Erwiński
Marcin PaprockiMarcin Paprocki
Marcin Paprocki
LGLech M Grzesiak
Lech M Grzesiak
KKKazimierz Karwowski
Kazimierz Karwowski
AWAndrzej Wawrzak
Andrzej Wawrzak
In computerized numerical control (CNC) systems, the communication bus between the controller and axis servo drives must offer high bandwidth, noise immunity, and time determinism. More and more CNC systems use real-time Ethernet protocols such as Ethernet Powerlink (EPL). Many modern controllers are closed costly hardware-based solutions. In this paper, the implementation of EPL communication bus in a PC-based CNC system is presented. The CNC system includes a PC, a software CNC controller running under Linux Real-Time Application Interface real-time operating system and servo drives communicating via EPL. The EPL stack was implemented as a real-time kernel module. Due to software-only implementation, this system is a cost-effective solution for a broad range of applications in machine control. All software systems are based on GNU General Public License or Berkeley Software Distribution licenses. Necessary modifications to the EPL stack, Linux configurations, computer basic input/output system, and motherboard configurations were presented. Experimental results of EPL communication cycle jitter on three different PCs were presented. The results confirm good performance of the presented system.

15 January 2022 in Energies
Verified
Journal Article
Open access
PDF file
Marcin PaprockiMarcin Paprocki
Marcin Paprocki
Krystian ErwińskiKrystian Erwiński
Krystian Erwiński
Synchronization between devices (in particular drive systems) is paramount for multi-axis motion control systems used in Computerized Numerical Control (CNC) machines, robots, and specialized technology machines used in many areas of the manufacturing industry. EtherCAT is an Ethernet-based network that is one of the most popular industrial networks for multi-axis motion control systems. EtherCAT is standardized in the IEC 61158 and IEC 61784 standards. In the article, an EtherCAT communication network for electrical drives is presented. The article focuses on the synchronization in the EtherCAT network consisting of one master device and slave servo drive devices. Special attention is given to synchronization mechanisms in EtherCAT, such as distributed clocks in slave servo drives devices. For this purpose, a laboratory stand was built consisting of two prototype servo drive devices with BLDC motors equipped with EtherCAT communication modules. A description of the working developed EtherCAT communication modules is given. Authors in communication modules ware used an EtherCAT Slave Controller (ESC) chip (AX58100) to implement lower EtherCAT layers. EtherCAT application layer was implemented in software form on a 32-bit microcontroller, based on CANopen over EtherCAT (CoE) CAN in Automation 402 (CiA402) profile. This research’s main contribution was to show the time dependencies regarding synchronization in terms of data flow in the EtherCAT communication stack in slave servo drive devices. The research results showed that the synchronous operation of drives is mainly influenced not by the mechanism of distributed clocks that ensures synchronization in the EtherCAT network but the implementation of the highest layer of the communication stack in slave servo drive devices. Experimental results are presented that prove the modules’ adequacy for use in high-performance motion control systems.

1 February 2022 in IEEE Transactions on Industrial Informatics
Verified
Journal Article
Closed access
Krystian ErwińskiKrystian Erwiński
Krystian Erwiński
AWAndrzej Wawrzak
Andrzej Wawrzak
Marcin PaprockiMarcin Paprocki
Marcin Paprocki
In this article, a NURBS toolpath feedrate profile generation algorithm for a biaxial linear motor control system is presented. High achievable velocities and accelerations of linear motor machines present new computational challenges in implementing feedrate generation and toolpath interpolation algorithms in real-time controllers. The proposed algorithm is capable of online generation of the feedrate profile with axial acceleration and jerk constraints. Each stage of the feedrate profiling algorithm is described with attention being given to both performance and implementation aspects. Furthermore, an alternative to the commonly used Taylor series interpolation method is also tested to ensure minimal interpolation errors. The feedrate profiling and interpolation algorithms’ implementation in a PC-based controller with real-time Linux kernel is described. Experimental results are presented that confirm that the algorithm is capable of limiting acceleration and jerk in the machine’s axes and it is low computation time enables real-time on-line operation in a PC-based CNC controller.

26 September 2016
Verified
Conference Paper
Closed access
Krystian ErwińskiKrystian Erwiński
Krystian Erwiński
Marcin PaprockiMarcin Paprocki
Marcin Paprocki
AWAndrzej Wawrzak
Andrzej Wawrzak
LGLech M Grzesiak
Lech M Grzesiak
This article presents a method for predicting contour error using artificial neural networks. Contour error is defined as the minimum distance between actual position and reference toolpath and is commonly used to measure machining precision of Computerized Numerically Controlled (CNC) machine tools. Offline trained Nonlinear Autoregressive networks with exogenous inputs (NARX) are used to predict following error in each axis. These values and information about toolpath geometry obtained from the interpolator are then used to compute the contour error. The method used for effective off-line training of the dynamic recurrent NARX neural networks is presented. Tests are performed that verify the contour error prediction accuracy using a biaxial CNC machine in a real-time CNC control system. The presented neural network based contour error predictor was used in a predictive feedrate optimization algorithm with constrained contour error.

25 April 2021
Verified
Conference Paper
Closed access
Krystian ErwińskiKrystian Erwiński
Krystian Erwiński
Marcin PaprockiMarcin Paprocki
Marcin Paprocki
GKGabriel Karasek
Gabriel Karasek
In state of the art computerized numerically controlled (CNC) machines toolpaths are often defined as polynomial Non-Uniform Rational B-Spline (NURBS) curves. This article investigates three main types of interpolation algorithms for NURBS toolpaths. These are Taylor series interpolation (TSI), predictor-corrector interpolation (PCI) and feedrate correction polynomial interpolation (FCPI). Interpolation accuracy of each method is investigated for an example NURBS toolpath. Interpolation computation time is also investigated for each method. Results are presented that compare the accuracy and computation efficiency of each method. It is shown that the Predictor-Corrector interpolation method achieves the best accuracy of the investigated methods without significant increase in computation time.

26 September 2016
Verified
Conference Paper
Closed access
Krystian ErwińskiKrystian Erwiński
Krystian Erwiński
Marcin PaprockiMarcin Paprocki
Marcin Paprocki
AWAndrzej Wawrzak
Andrzej Wawrzak
LGLech M Grzesiak
Lech M Grzesiak
Generation of a time-optimal feedrate profile for CNC machines has received significant attention in recent years. Most methods focus on achieving maximum allowable feedrate with constrained axial acceleration and jerk without considering manufacturing precision. Manufacturing precision is often defined as contour error which is the distance between desired and actual toolpaths. This paper presents a method of determining the maximum feedrate for NURBS toolpaths while constraining velocity, acceleration, jerk and contour error. Contour error is predicted during optimization by using an artificial neural-network. Optimization is performed by Particle Swarm Optimization with Augmented Lagrangian constraint handling technique. Results of a time-optimal feedrate profile generated for an example toolpath are presented to illustrate the capabilities of the proposed method.