Marija Milijić

Dr. Marija Milijić

The Faculty of Electronic Engineering, University of Nis, Niš, Serbia
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 June 2015 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
Marija MilijićMarija Milijić
Marija Milijić
ANAleksandar D. Nesic
Aleksandar D. Nesic
BMBratislav Milovanovic
Bratislav Milovanovic
The detailed research, full development, and experimental realization of a new printed antenna array with cosecant squared-shaped beam pattern are presented. Some advantages of proposed antenna, as compared to previously realized microstrip cosecant-squared pattern antennas, are pointed out. The suggested antenna, which targets X frequency range, has significantly better bandwidth characteristics thanks to its symmetrical radiating elements of pentagonal shape. The symmetrical feeding network of impedance transformers provides necessary amplitude's and phase's distributions obtained by Orchard Elliott's methods and genetic algorithm. Furthermore, it is on the same substrate as antenna, making entire concept simple, easy, and cheap for realization. Moreover, the antenna is in a corner reflector, which enables achieving relatively high gain. The proposed antenna is validated by simulations and measurements. The measured radiation pattern barely varies from theoretical radiation pattern. Realized antenna has gain above 15 dBi and sidelobe suppression greater than 20 dB at the center frequency of 10 GHz.

12 August 2025 in Sensors
Verified
Journal Article
Open access
PDF file
Marija MilijićMarija Milijić
Marija Milijić
BJBranka Jokanovic
Branka Jokanovic
MTMiodrag Tasic
Miodrag Tasic
SJSinisa Jovanovic
Sinisa Jovanovic
OBOlga Boric-Lubecke
Olga Boric-Lubecke
VLVictor Manuel Lubecke
Victor Manuel Lubecke
This paper presents the novel design of a printed, low-cost, dual-port, and dual-polarized slot antenna for microwave biomedical radars. The butterfly shape of the radiating element, with orthogonally positioned arms, enables simultaneous radiation of both vertically and horizontally polarized waves. The antenna is intended for full-duplex in-band applications using two mutually isolated antenna ports, with the CPW port on the same side of the substrate as the slot antenna and the microstrip port positioned orthogonally on the other side of the substrate. Those two ports can be used as transmit and receive ports in a radar transceiver, with a port isolation of 25 dB. Thanks to the bow-tie shape of the slots and an additional coupling region between the butterfly arms, there is more flexibility in simultaneous optimization of the resonant frequency and input impedance at both ports, avoiding the need for a complicated matching network that introduces the attenuation and increases antenna dimensions. The advantage of this design is demonstrated through the modeling of an eight-element dual-port linear array with an extremely simple feed network for high-gain biosensing applications. To validate the simulation results, prototypes of the proposed antenna were fabricated and tested. The measured operating band of the antennas spans from 2.35 GHz to 2.55 GHz, with reflection coefficients of less than—10 dB, a maximum gain of 8.5 dBi, and a front-to-back gain ratio that is greater than 15 dB, which is comparable with other published single dual-port slot antennas. This is the simplest proposed dual-port, dual-polarization antenna that enables straightforward scaling to other frequency bands.

20 May 2025 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Open access
JIJon H. Itokazu
Jon H. Itokazu
Marija MilijićMarija Milijić
Marija Milijić
BJBranka Jokanović
Branka Jokanović
OBOlga Boric-Lubecke
Olga Boric-Lubecke
VLVictor Manuel Lubecke
Victor Manuel Lubecke
Physiological radar measurements are used to extract biomedical motion data from body scattered radio signals. These often-faint reflected signals undergo both Doppler-phase and polarization alterations. Polarimetric analysis of physiological radar measurements can provide insight into the nature of the scattering mechanism and lead to the development of methods for enhancing the signal-to-noise ratio (SNR) for such systems and potentially expand the range of biomedical data which can be extracted. This article presents a comprehensive polarimetric study of physiological Doppler radar signatures and reports on an empirical study intended to examine polarimetric scattering associated with human respiration. A compact dual-polarization antenna was employed in a full-polarimetric configuration and a dual-receive configuration, enabling precise polarimetric measurements. Simulation and experimental results with robotic respiratory phantoms and human subjects demonstrated consistent levels of cross-polarized scattering across configurations and revealed a complex nature for cross-polarized signal generation from robotic targets and human subjects. Cross-polarized amplitudes of up to 15.6% of co-polarized amplitudes were observed for robotic phantoms, while a wide range was observed for human subjects with most at 70% or less, while in some cases amplitudes as high as 198% of co-polarized amplitudes were observed. The results indicate that a significant, yet difficult to predict, amount of polarization rotation occurs from both vertical and horizontal transmit polarizations, and that for either incident polarization there is no clear preference for co-polarized received signals. Thus, there is significant potential for improved SNR and signature content via polarimetric radar systems which can transmit and/or receive signals with complementary polarizations.

4 April 2018 in Frequenz
Verified
Journal Article
Closed access
PDF file
Marija MilijićMarija Milijić
Marija Milijić
ANAleksandar D. Nešić
Aleksandar D. Nešić
BMBratislav D. Milovanović
Bratislav D. Milovanović
DNDusan Nesic
Dusan Nesic
A printed antenna array consisting of 10 wideband symmetrical pentagonal dipoles is presented. The feed network of impedance transformers is employed to provide appropriate amplitude and phase distribution necessary to obtain flat top beam pattern. The measured results demonstrate excellent radiation characteristics including 38° flat gain region with maximum ripple of 3.5 dB at the centre frequency. Furthermore, the proposed antenna that is placed in corner reflector with angle of 60° has good gain (17 dBi) and side lobe suppression (18.9 dB). Although it is designed at the centre frequencyfc=12 GHz, it was shown to be capable of shaping a good flat top radiation pattern within a fractional bandwidth at least 6 % of centre frequency. Also, proposed antenna features cheap, simple and easy fabrication that makes it suitable for mass production.

1 October 2015
Verified
Conference Paper
Closed access
Marija MilijićMarija Milijić
Marija Milijić
ANAleksandar Nesic
Aleksandar Nesic
BMBratislav Milovanovic
Bratislav Milovanovic
NDNebojsa Doncov
Nebojsa Doncov
IRIvana Radnovic
Ivana Radnovic
The paper investigates the feeding structures for printed antenna arrays with parallel reflector and their influences on antenna parameters. Two printed antenna arrays are presented. The first consists of ten series fed symmetrical dipoles with tapered impedances. The second is the array of eight symmetrical dipoles that are fed by a tapered distribution. The feeding structures for both antennas are realized in symmetrical (balanced) microstrip technique eliminating surface wave effect. However, a parasitic radiation from a feeding network cannot be avoided and it affects antenna performances, especially side lobe suppression. This influence is the most obvious for the antenna with parallel reflector where there is not isolation between array and feeding structure.

1 January 2026
Verified
Conference Paper
Closed access
ZMZlatica Marinkovic
Zlatica Marinkovic
BSBiljana P. Stosic
Biljana P. Stosic
Marija MilijićMarija Milijić
Marija Milijić
DMDušan Marković
Dušan Marković
Girolamo TagliapietraGirolamo Tagliapietra
Girolamo Tagliapietra
Jacopo IANNACCIJacopo IANNACCI
Jacopo IANNACCI
This paper presents an efficient approach for the analysis of a W-band RF-MEMS switch based on an artificial neural network (ANN) model of the switch return and insertion losses. The analysis is performed over the 92–95 GHz frequency range, with particular emphasis on the influence of the switch recess dimension. In the proposed ANN modeling approach, the recess dimension is used as the primary input parameter. Two separate ANN models are employed to capture the frequency dependence of the return and insertion losses. Moreover, a power flow analysis is carried out by converting the modeled return and insertion losses into reflected, transmitted, and absorbed power components. The developed ANN model enables fast and accurate evaluation of loss characteristics and power distribution, facilitating efficient parametric studies and design optimization of W-band RF-MEMS switches.