This work presents an extensive, comparative study of the gamma and electron radiation effects on the behaviour of femtosecond laser-inscribed fibre Bragg gratings (FBGs) using the point-by-point and plane-by-plane inscription methods. The FBGs were inscribed in standard telecommunication single mode silica fibre (SMF28) and exposed to a total accumulated radiation dose of 15 kGy for both gamma and electron radiation. The gratings’ spectra were measured and analysed before and after the exposure to radiation, with complementary material characterisation using Fourier transform infrared (FTIR) spectroscopy. Changes in the response of the FBGs’ temperature coefficients were analysed on exposure to the different types of radiation, and we consider which of the two inscription methods result in gratings that are more robust in such harsh environments. Moreover, we used the FTIR spectroscopy to locate which chemical bonds are responsible for the changes on temperature coefficients and which are related with the optical characteristics of the FBGs.

In this paper, we propose a highly selective and efficient gas detection system based on a narrow-band IR metasurface emitter integrated with a resistive heater. In order to develop the sensor for the detection of specific gases, both the microheater and metasurface structures have been optimized in terms of geometry and materials. Devices with different metamaterial structures and geometries for the heater have been tested. Our prototype showed that the modification of the spectral response of metasurface-based structures is easily achieved by adapting the geometrical parameters of the plasmonic micro-/nanostructures in the metasurface. The advantage of this system is the on-chip integration of a thermal source with broad IR radiation with the metasurface structure, obtaining a compact selective radiation source. From the experimental data, narrow emission peaks (FWHM as low as 0.15 μm), corresponding to the CO₂, CH₄, and CO absorption bands, with a radiant power of a few mW were obtained. It has been shown that, by changing the bias voltage, a shift of a few tens of nm around the central emission wavelength can be obtained, allowing fine optimization for gas detection applications.

In this work, we present a new setup for real-time investigations of optical fibers and optical fiber sensors while being subjected to gamma-rays. The investigation of the radiation effects on novel or well-assessed sensing devices has attracted a lot of interest, however, the facilities required to do this (when available) are barely accessible to the device to be characterized. In order to reduce the limitations of these types of experiments and ensure a highly controlled environment, we implemented a configuration that permits the on-line testing of optical components inside a Co-60 gamma chamber research irradiator. To show the advantages of this new approach, we present a case study that compares an arc-induced optical fiber long period grating (LPG) irradiated in a gamma chamber with the same type of grating irradiated with gamma-rays from a Co-60 industrial irradiator. In order to better understand the effects of radiation on such components and their behavior in radiation environments, we focus on the homogeneity of the radiation field and parameter customizability as well as the high reproducibility of the experiments.

Hexagonal ZnO nanowires were grown using the PLD/VLS technique on a SAW sensor active area for hydrogen sensing. The influence of different carbon and nitrogen surface contaminant concentrations on sensor output was investigated for three active area cases: a few weeks’ exposure to free ambient air contamination, 3 h at 600 °C thermal desorption of carbon, and (room temperature) plasma-activated nitrogen and carbon contamination. Correlations between sensing performance and contamination element concentration were established. To understand the adsorption versus absorption mechanisms, similar studies were further performed on circular ZnO nanowires morphology, which have a different surface-area-to-volume ratio. Comparative results show that, while a 20% carbon surface contamination variation generates a variation of 3–5% in nanostructure hydrogen sorption, nitrogen surface contamination influence depends on nanostructure morphology. Thus, in our comparative studies, for the case of a nanowire hexagonal cross-section a 12% nitrogen surface contamination variation generates a 5–7% increase in hydrogen adsorption and also an increase of 6–8% in hydrogen absorption. Consequently, the catalytic effect of nitrogen could enlarge the linear response of nanowire-based (SAW) sensors over a wider hydrogen concentration range.