Mohamed Ammar

Mr. Mohamed Ammar

Department of Mechanical and Aerospace Engineering, Monash University
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 March 2021 in Sensors
Verified
Journal Article
Open access
PDF file
WWWeichen WEI
Weichen WEI
Bijan ShirinzadehBijan Shirinzadeh
Bijan Shirinzadeh
RNRohan Nowell
Rohan Nowell
MGMohammadali Ghafarian
Mohammadali Ghafarian
MAMohamed Ammar
Mohamed Ammar
TSTianyao Shen
Tianyao Shen
Solid-State LiDAR (SSL) takes an increasing share of the LiDAR market. Compared with traditional spinning LiDAR, SSLs are more compact, energy-efficient and cost-effective. Generally, the current study of SSL mapping is limited to adapting existing SLAM algorithms to an SSL sensor. However, compared with spinning LiDARs, SSLs are different in terms of their irregular scan patterns and limited FOV. Directly applying existing SLAM approaches on them often increase the instability of a mapping process. This study proposes a systematic design, which consists of a dual-LiDAR mapping system and a three DOF interpolated six DOF odometry. For dual-LiDAR mapping, this work uses a 2D LiDAR to enhance a 3D SSL performance on a ground vehicle platform. The proposed system takes a 2D LiDAR to preprocess the scanning field into a number of feature sections according to the curvatures on the 2D fraction. Subsequently, this section information is passed to 3D SSL for direction feature selection. Additionally, this work proposes an odometry interpolation method which uses both LiDARs to generate two separated odometries. The proposed odometry interpolation method selectively determines the appropriate odometry information to update the system state under challenging conditions. Experiments are conducted in different scenarios. The results proves that the proposed approach is able to utilise 12 times more corner features from the environment than the comparied method, thus results in a demonstrable improvement in its absolute position error.

1 July 2021 in Composite Structures
Verified
Journal Article
Closed access
MAMohamed Ammar
Mohamed Ammar
BSBijan Shirinzadeh
Bijan Shirinzadeh
PZPan Zhao
Pan Zhao
YSYaoyao Shi
Yaoyao Shi

24 February 2022 in Aerospace Science and Technology
Verified
Journal Article
Closed access
MAMohamed Ammar
Mohamed Ammar
BSBijan Shirinzadeh
Bijan Shirinzadeh
PZPan Zhao
Pan Zhao
YSYaoyao Shi
Yaoyao Shi

9 November 2021 in Sensors
Verified
Journal Article
Open access
PDF file
MAMohamed Ammar
Mohamed Ammar
BSBijan Shirinzadeh
Bijan Shirinzadeh
KLKai Zhong Lai
Kai Zhong Lai
WWWeichen WEI
Weichen WEI
The current study presents three calibration approaches for the hole-drilling method (HDM). A total of 72 finite element models and 144 simulations were established to calibrate the measurements of the strain sensors. The first approach assumed the stresses acted on the boundaries of the drilled hole and thus analyzed the surrounding displacements field. The second analysis considered the loads on the outer surfaces of the specimen while measuring the strains’ differences between the model with and without the drilled hole. The third approach was more comprehensive as it considered the mechanical and thermal effects of the drilling operations. The proposed approaches were applied to two different materials (AISI 1045 and CFRP). The steel specimens were machined using a CNC lathe while the composite laminates were manufactured using the robotic fiber placement (RFP) process. Subsequently, the residual stresses (RSs) were measured using the HDM. The obtained data were compared with X-ray diffraction measurements for validation. The results showed better estimation of the RSs when utilizing the third approach and clear underestimation of the stresses using the second approach. A divergence in RSs values between the three approaches was also detected when measuring the stresses in the internal layers of the composite laminates.

14 May 2022 in Polymer Composites
Verified
Journal Article
Open access
MAMohamed Ammar
Mohamed Ammar
BSBijan Shirinzadeh
Bijan Shirinzadeh
The robotic fiber placement (RFP) process depends on continuous fusion bonding and solidifying of prepreg tows onto a substrate by subjecting them to a compression force and heat flux. However the advantages provided when using the RFP to fabricate the composite structures, it has adverse effects due to the induced residual stresses (RSs). The current work presents the effect of the RFP on the induced RSs in thermoset composites. RFP is utilized to fabricate specimens from carbon fiber reinforced polymers. Effects of placement speed, compression force, heating temperature, heating gas flowrate, and the location of the heat flux outlet nozzle are all included in the present study. A total of 69 flat panels are manufactured under different process conditions. Subsequently, the in‐depth RSs are measured using the incremental hole‐drilling method. Besides, the microstructures of the samples are also analyzed. The results show that the change in process parameters could significantly affect the induced RSs of the thermoset composites. Subjecting the samples to higher thermal and pressure loads would induce more RSs, which are attributed to the occurrence of partial curing during the manufacturing process along with the change in laminate geometry and porosity.

6 November 2022 in Sensors
Verified
Journal Article
Open access
PDF file
MAMohamed Ammar
Mohamed Ammar
Bijan ShirinzadehBijan Shirinzadeh
Bijan Shirinzadeh
HGHassan El Gamal
Hassan El Gamal
MNMohamed N. A. Nasr
Mohamed N. A. Nasr
This study focuses on the role of the damage evolution when estimating the failure behavior of AISI 1045 steel for sensing and measuring metal cutting parameters. A total of five Lagrangian explicit models are established to investigate the effect of applying damage evolution techniques. The Johnson–Cook failure model is introduced once to fully represent damage behavior, i.e., no damage evolution is considered, and as a damage initiation criterion in the remaining approaches. A fracture energy-based model is included to model damage propagation with different evolution rates. Temperature-dependent and temperature-independent fracture energy models are also investigated. Dry orthogonal cutting and residual stresses measurements of AISI 1045 are conducted for validation. The significance of the damage evolution is investigated using honed-tool and sharp-tool models. Including the damage evolution led to a prediction of higher workpiece temperatures, plastic strains, cutting forces, and residual stresses, with no clear differences between linear and exponential evolution rates. The role of damage evolution is more evident when temperature-dependent evolution models are used.