The tensile and compressive behaviors of 316L stainless steel at room temperature were compared. The differences between the stress–strain responses during tension and compression were explained by the different evolutions of the texture, defect structure, and phase composition. It was found that up to true strain of ~ 25 pct the flow stress during tension was only slightly higher (by ~ 40 MPa) than that during compression, which can be explained by the different textures of the two types of specimens. On the other hand, between the strains of 25 and 50 pct, the strain hardening for tension was much higher, which resulted in a ~ 200 MPa larger flow stress in the tensile-tested specimen at 50 pct strain. It was revealed that the higher flow stress in tension was caused by the harder texture, the higher dislocation density, and the larger fraction of martensite phase.
An ultrafine-grained (UFG) Al-4.8%Zn-1.2%Mg-0.14%Zr (wt%) alloy was processed by high pressure torsion (HPT) technique and then aged at 120 and 170 °C for 2 h. The changes in the microstructure due to this artificial aging were studied by X-ray diffraction and transmission electron microscopy. It was found that the HPT-processed alloy has a small grain size of about 200 nm and a high dislocation density of about 8 × 1014 m−2. The majority of precipitates after HPT are Guinier–Preston (GP) zones with a size of ~ 2 nm, and only a few large particles were formed at the grain boundaries. Annealing at 120 and 170 °C for 2 h resulted in the formation of stable MgZn2 precipitates from a part of the GP zones. It was found that for the higher temperature the fraction of the MgZn2 phase was larger and the dislocation density in the Al matrix was lower. The changes in the precipitates and the dislocation density due to aging were correlated to the hardness evolution. It was found that the majority of hardness reduction during aging was caused by the annihilation of dislocations and some grain growth at 170 °C. The aging effect on the microstructure and the hardness of the HPT-processed specimen was compared to that observed for the UFG sample processed by equal-channel angular pressing. It was revealed that in the HPT sample less secondary phase particles formed in the grain boundaries, and the higher amount of precipitates in the grain interiors resulted in a higher hardness even after aging.
Ultrafine-grained Cu/Al/Ag composites were processed by an accumulative roll bonding (ARB) technique from pure copper and aluminum sheets and a silver powder. The Al content was fixed to 11 wt.% while the silver concentration was 1, 2, or 3 in wt.%. The ARB-processed samples were heat treated at different temperatures between 750 and 1050 °C for 60 min and then quenched to room temperature (RT) for producing Cu–Al–Ag alloys. The effect of the addition of different Ag contents and various heat treatment temperatures on the structural evolution was investigated. The ARB-processed samples were composed of Cu and Al layers with high dislocation density and fine grain size (a few microns). During heat treatment of the ARB-processed samples, new intermetallic phases formed. For the lowest Ag content (1 wt.%), the main phase was a brittle simple cubic Al4Cu9, while for higher Ag concentrations (2 and 3 wt.%), the quenched samples contain mainly an orthorhombic β1-AlCu3 martensite phase. The martensite phase consisted of very fine lamellas with a thickness of one micron or less. The heat treatment increased the microhardness and the strength of the samples at RT due to the formation of a fine-grained hard martensite phase. For 2 and 3% Ag, the highest martensite phase content was achieved at 850 and 950 °C, respectively. The annealed and quenched samples exhibited good shape memory behavior at RT.
Electrodeposited Ni65Co35/Cu multilayers were prepared with Cu spacer layer thicknesses between 0.5 nm and 7 nm. Their structure and magnetic and magnetoresistance properties were investigated. An important feature was that the Cu layers were deposited at the electrochemically optimized Cu deposition potential, ensuring a reliable control of the spacer layer thickness to reveal the true evolution of the giant magnetoresistance (GMR). X-ray diffraction indicated satellite reflections, demonstrating the highly coherent growth of these multilayer stacks. All of the multilayers exhibited a GMR effect, the magnitude of which did not show an oscillatory behavior with spacer layer thickness, just a steep rise of GMR around 1.5 nm and then, after 3 nm, it remained nearly constant, with a value around 4%. The high relative remanence of the magnetization hinted at the lack of an antiferromagnetic coupling between the magnetic layers, explaining the absence of oscillatory GMR. The occurrence of GMR can be attributed to the fact that, for spacer layer thicknesses above about 1.5 nm, the adjacent magnetic layers become uncoupled and their magnetization orientation is random, giving rise to a GMR effect. The coercive field and magnetoresistance peak field data also corroborate this picture: with increasing spacer layer thickness, both parameters progressively approached values characteristic of individual magnetic layers. At the end, a critical analysis of previously reported GMR data on electrodeposited Ni-Co/Cu multilayers is provided in view of the present results. A discussion of the layer formation processes in electrodeposited multilayers is also included, together with a comparison with physically deposited multilayers.
17 April 2026 in The European Physical Journal Plus