This paper presents the design and characterization of a compact broadband antenna and its MIMO configuration for 28 GHz 5G applications. The antenna was designed using Rogers RT/5880 with a thickness of 1.575 mm and has an overall compact size of 30 mm × 30 mm. The design methodology was initiated by designing a compact conventional microstrip antenna for 28 GHz. Afterward, the rectangular slots were utilized to improve the impedance bandwidth so that antenna covers the globally allocated 28 GHz band spectrum for 5G applications. Furthermore, a compact 2 × 2 MIMO antenna with polarization diversity is designed for high channel capacity systems. The mutual coupling between the closely spaced antenna elements is reduced by using two consecutive iterations of defected ground structure (DGS). The proposed MIMO antenna system offers broad bandwidth, high gain, low mutual coupling, and low envelope correlation coefficient along with high diversity gain, low mean effective gain, and low channel capacity loss. Moreover, the proposed been compared with the state-of-the-art MIMO antenna proposed for 28 GHz application to demonstrate worth of the presented design.

Metamaterials exhibit properties in terms of subwavelength operation or phase manipulation, among others, that can be used in a variety of applications in 5G communication systems. The future and current 5G devices demand high efficiency, high data rate, computational capabilities, cost-effectiveness, compact size, and low power consumption. This variation and advancement are possible when the antenna design is revised to operate over wideband, high gain, and multiband and has characteristics of compact size, reconfiguration, absorption, and simple ease of fabrication. The materials loaded with antennas or, in the same cases, without antennas, offer the aforementioned characteristics to bring advancement in order to facilitate users. A number of works on designing metasurfaces capable of improving bandwidth, gain efficiency, and reducing the size and cost of antennas are available in the literature for this purpose. Not only are these applications possible, but the intelligent metasurfaces are also designed to obtain reconfiguration in terms of frequency and polarization. The number of absorbers loaded with metamaterials is also designed to improve the absorption percentage used for radar applications. Thus, in this paper, the general overview of different types of metamaterials and their role in performance enhancement and application in 5G and 6G communication systems is discussed.

A dual-band, compact, high-gain, simple geometry, wideband antenna for 5G millimeter-wave applications at 28 and 38 GHz is proposed in this paper. Initially, an antenna operating over dual bands of 28 and 38 GHz was designed. Later, a four-port Multiple Input Multiple Output (MIMO) antenna was developed for the same dual-band applications for high data rates, low latency, and improved capacity for 5G communication devices. To bring down mutual coupling between antenna elements, a parasitic element of simple geometry was loaded between the MIMO elements. After the insertion of the parasitic element, the isolation of the antenna improved by 25 dB. The suggested creation was designed using a Rogers/Duroid RT-5870 laminate with a thickness of 0.79 mm. The single element proposed has an overall small size of 13 mm × 15 mm, while the MIMO configuration of the proposed work has a miniaturized size of 28 mm × 28 mm. The parasitic element-loaded MIMO antenna offers a high gain of 9.5 and 11.5 dB at resonance frequencies of 28 GHz and 38 GHz, respectively. Various MIMO parameters were also examined, and the results generated by the EM tool CST Studio Suite^® and hardware prototype are presented. The parasitic element-loaded MIMO antenna offers an Envelop Correlation Coefficient (ECC) < 0.001 and Channel Capacity Loss (CCL) < 0.01 bps/Hz, which are quite good values. Moreover, a comparison with existing work in the literature is given to show the superiority of the MIMO antenna. The suggested MIMO antenna provides good results and is regarded as a solid candidate for future 5G applications according to the comparison with the state of the art, results, and discussion.

Dielectrics are non‐conducting substances that are primarily utilized to hold electric charges. These materials are widely employed in the field of chemical mechanical, civil and structural engineering, because of their inherent insulating properties. Besides these domains, dielectric materials are also used in electrical and electronic applications. Dielectric materials have shown an ever‐increasing potential in recent years in the fabrication of antennas, sensors, and optical devices that are extensively utilized for on‐body, environmental, robotics, and biomedical applications. With inherent electrostatic shielding, insulation, and dielectric relaxations, these materials are used in intelligent electronic devices used for biomedical applications, smart devices, vehicles, and future IoT applications. Numerous applications necessitate multiple kinds of dielectric, classified based on their polarization, flexibility, thickness, dielectric constant, and specific application. In this extensive research review, the characteristics and various aspects of dielectric materials are discussed, followed by a thorough and detailed review of flexible dielectrics and their usage in flexible electronics. Additionally, the practicality and applications of these materials which come from a variety of publications in the literature are also discussed. Moreover, in‐depth study of dieletrics in sensors and RF applications are performed.

For ISM, WLAN, and C-band applications, a multiple-stub loaded CPW feed tri-band antenna is presented in this study. The suggested antenna uses Rogers RT/Duroid 5880 substrate material with a 0.79 mm thickness. The antenna has a straightforward design, measures just 33 mm × 20 mm, and provides broad performance with excellent gain. A 4-port MIMO arrangement is subsequently used to fulfill the demands of upcoming 5G and 6G devices. The MIMO antenna contains little space between elements and offers a good value of < –30 dB isolation. The overall size of a 4-port MIMO antenna is M_W × M_L × H = 60 mm × 60 mm × 0.79 mm and offers a minimum value of ECC <0.0001. Besides ECC, the MIMO antenna also offers good results in terms of DG, CCL, and MEG. To validate the findings of the simulation, a hardware prototype of the suggested antenna is created. It is clear that the results from simulations and measurements coincide well. The proposed antenna was created with the aid of the software tool Ansoft HFSSv9. Also, the proposed work is evaluated against previously published material. The suggested antenna has a small size, a simple geometry, a wideband, high gain, and a good value for the MIMO parameters, according to the results and comparisons of the proposed work (in terms of ECC, DG, CCL, and MEG), and low spacing between elements, which makes it a promising candidate for future 5G devices operating over ISM, WLAN, and C–band applications.

In this article, a single-layer frequency selective surface (FSS)-loaded compact coplanar waveguide (CPW)-fed antenna is proposed for very high-gain and ultra-wideband applications. At the initial stage, a geometrically simple ultra-wideband (UWB) antenna is designed which contains CPW feed lines and a multi-stub-loaded hexagonal patch. The various stubs are inserted to improve the bandwidth of the radiator. The antenna operates at 5–17 GHz and offers 6.5 dBi peak gain. Subsequently, the proposed FSS structure is designed and loaded beneath the proposed UWB antenna to improve bandwidth and enhance gain. The antenna loaded with FSS operates at an ultra-wideband of 3–18 GHz and offers a peak gain of 10.5 dBi. The FSS layer contains 5 × 5 unit cells with a total dimension of 50 mm × 50 mm. The gap between the FSS layer and UWB antenna is 9 mm, which is fixed to obtain maximum gain. The proposed UWB antenna and its results are compared with the fabricated prototype to verify the results. Moreover, the performance parameters such as bandwidth, gain, operational frequency, and the number of FSS layers used in the proposed antenna are compared with existing literature to show the significance of the proposed work. Overall, the proposed antenna is easy to fabricate and has a low profile and simple geometry with a compact size while offering a very wide bandwidth and high gain. Due to all of its performance properties, the proposed antenna system is a strong candidate for upcoming wideband and high-gain applications.