As Malaysia is a fast-developing country, its prospects of sustainable energy generation are at the center of debate. Malaysian municipal solid waste (MSW) is projected to have a 3-5% increase in annual generation rate at the same time an increase of 4-8% for electricity demand. In Malaysia, most of the landfills are open dumpsite and 89% of the collected MSW end up in landfills. Furthermore, huge attention is being focused on converting MSW into energy due to the enormous amount of daily MSW being generated. Sanitary landfill to capture methane from waste landfill gas (LFG) and incineration in a combined heat and power plant (CHP) are common MSW-to-energy technologies in Malaysia. MSW in Malaysia contains 45% organic fraction thus landfill contributes as a potential LFG source. Waste-to-energy (WTE) technologies in treating MSW potentially provide an attractive economic investment since its feedstock (MSW) is collected almost for free. At present, there are considerable issues in WTE technologies although the technology employing MSW as feedstock are well established, for instance the fluctuation of MSW composition and the complexity in treatment facilities with its pollutant emissions. Thus, this study discusses various WTE technologies in Malaysia by considering the energy potentials from all existing incineration plants and landfill sites as an effective MSW management in Malaysia. Furthermore, to promote local innovation and technology development and to ensure successful long-term sustainable economic viability, social inclusiveness, and environmental sustainability in Malaysia, the four faculties of sustainable development namely technical, economic, environmental, and social issues affiliated with MSW-to-Energy technologies were compared and evaluated.

Anaerobic digestion (AD) appears to be a popular unit operation in wastewater treatment plant to treat waste activated sludge (WAS) and the produced methane gas can be harvested as renewable energy. However, WAS could inhibit hydrolysis stage during AD and hence pre-treatment is required to overcome the issue. This paper aimed to study the effect of electrochemical pre-treatment (EP) towards efficiency of AD using titanium coated with ruthenium oxide (Ti/RuO₂) electrodes. The investigation has been carried out using in-house laboratory batch-scale mesophilic anaerobic digester, mixed under manipulation of important operating parameters. Optimization was performed on EP using response surface methodology and central composite design to maximize sludge disintegration and dewaterability. By operating at optimal conditions (pH 11.65, total solids 22,000 mg/L, electrolysis time 35 min, current density 6 mA/cm², and 1000 mg/L of sodium chloride), the pre-treated WAS in terms of mixed liquor volatile suspended solids (MLVSS) removal, soluble chemical oxygen demand (sCOD), capillary suction time (CST) reduction, and extracellular polymeric substance (EPS) were 38%, 4800 mg/L (increased from 935 mg/L), 33%, and 218 mg/L, respectively. Following AD, the volatile solids (VS) removal and chemical oxygen demand (COD) removal by EP were enhanced from 40.7% and 54.7% to 47.2% and 61.5%, respectively, at steady-state. The biogas produced from control and electrochemical pre-treated WAS were in the ranges of 0.12 to 0.17 and 0.2 to 0.24 m³/kg VS_fed, respectively, and the volume of biogas produced was 44–67% over the control. Based on the results obtained, suitability of EP for WAS prior to AD was confirmed.

Defining project success is an elusive topic. The lack of an agreed definition for project success has long been the reason for failing to define and evaluate success. In fact, the matter of whether or not it is necessary to define success remains a huge doubt. The topic may become more complicated in the context of construction industry. The reasons are high inherent risk, one-of-a-kind end product and vulnerable to various uncertainties. As the construction project success expands rapidly, the need for identification of new research area increases simultaneously. This paper, therefore, provides a review of the project success notions and proposes a conceptual framework that identifies the relationship between success factors and criteria as a new research area in construction project success. This paper will help researcher to identify the most devoted notions of construction success and attract more researches to enhance the construction project success.

Stabilized landfill leachate contains a wide variety of highly concentrated non-biodegradable organics, which are extremely toxic to the environment. Though numerous techniques have been developed for leachate treatment, advanced membrane filtration is one of the most environmentally friendly methods to purify wastewater effectively. In the current study, a novel polymeric membrane was produced by integrating powdered activated carbon (PAC) on polyvinylidene fluoride (PVDF) to synthesize a thin membrane using the phase inversion method. The membrane design was optimized using response surface methodology (RSM). The fabricated membrane was effectively applied for the filtration of stabilized leachate using a cross-flow ring (CFR) test. The findings suggested that the filtration properties of fabricated membrane were effectively enhanced through the incorporation of PAC. The optimum removal efficiencies by the fabricated membrane (14.9 wt.% PVDF, 1.0 wt.% PAC) were 35.34, 48.71, and 22.00% for COD, colour and NH₃-N, respectively. Water flux and transmembrane pressure were also enhanced by the incorporated PAC and recorded 61.0 L/m²·h and 0.67 bar, respectively, under the conditions of the optimum removal efficiency. Moreover, the performance of fabricated membranes in terms of pollutant removal, pure water permeation, and different morphological characteristics were systematically analyzed. Despite the limited achievement, which might be improved by the addition of a hydrophilic additive, the study offers an efficient way to fabricate PVDF-PAC membrane and to optimize its treatability through the RSM tool.