In this study, the effect of location of surcharge load on the stability and behavior of the retaining wall under static and dynamic load has been considered. A cantilever retaining wall of 7 m height retained dry sandy soil with 50 kN/m 2 surcharge load. Several parameters were taken into account in the numerical analysis, including the horizontal distance ( X ) from the edge of the wall to the surcharge load expressed as a ratio to the heel width (
X/B
h = 0, 0.25, 0.5, 0.75, and 1), as well as the effect of different values of the earthquake's horizontal component (
k
h = 0.1, 0.2, and 0.3). Lateral earth pressure distribution decreases with increase ( X / Bh ) in the upper one third of the wall. The effect of surcharge location at the top of the wall disappears at X / Bh = 0.25. Under dynamic load, the maximum displacement at the top of the wall is obtained at X / Bh = 0.5. It is increased by about 4 times at kh = 0.3. The possibility of sliding increases by about 4.8 times once the kh increases from 0.1 to 0.3. There is a maximum increase in rotation by 2 times at kh = 0.1. In the dynamic case, the differential settlement decreases with increase in X / Bh , and increases with the increase in kh .
The distribution of contact stresses beneath shallow foundations governs both structural demand within the footing and the deformation response of the supporting soil. Although numerous analytical and numerical studies have investigated soil–foundation interaction, the combined influence of foundation geometry and embedment ratio on contact stress distribution, settlement behavior, stress bulb development, and foundation rigidity has not been systematically evaluated within a unified numerical framework. This study presents a comprehensive finite element investigation of shallow foundations with circular, square, and strip geometries subjected to four embedment ratios (Df/B, where Df denotes the embedment depth and B the footing width) of 0.25, 0.50, 0.75, and 1.00, considering six representative soil profiles ranging from soft clay to dense sand. A total of 216 numerical simulations were performed using PLAXIS 2D (version 2024.1) under drained conditions, employing the Mohr–Coulomb constitutive model. The numerical setup was checked against classical analytical stress and settlement solutions under corresponding idealized conditions. The results demonstrate that increasing embedment consistently reduces peak contact stresses, decreases foundation settlement, and produces shallower stress bulbs over the investigated range of Df/B. Within the adopted 2D numerical framework, the circular-footing representation exhibits the most uniform contact stress distribution and the lowest settlements, whereas the strip-footing representation develops the highest stress concentrations and deepest influence zones. In addition, a depth-adjusted formulation of the Relative Stiffness Factor is proposed to account for the increase in operative soil stiffness associated with embedment, providing a framework for evaluating the relative rigidity of embedded foundations. The findings provide quantitative insight into the influence of foundation geometry and embedment depth on stress transfer and settlement performance, thereby supporting the comparative assessment of shallow foundation behavior within the investigated conditions.
28 August 2025 in Journal of University of Babylon for Engineering Sciences
In this study the Artificial Intelligent Method (AIM) was used to find safety factors against sliding, overturning and bearing capacity of cantilever type retaining wall. The method was also used to determine the optimum dimensions of retaining wall and consequently minimum retaining wall volume. Three parameters were investigated in this study: friction of the soil beneath and behind the retaining wall ( ), retaining wall height (H) and surcharge load (Q). approximately, zero constrains violation and constant volume of retaining wall were achieved through three iterations of solution. This results gave a reliability for using this method for optimum design of cantilever type retaining wall. The results demonstrated that, the significant increasing in sliding and bearing capacity factors of safety started at ( ), while the safety factor against overturning decreased with increasing soil friction up to ( ) and then increased. On the other hand, there is no change in base width of retaining wall when ( ) excessed ( ), and the optimum volume of retaining wall decreased significantly at this value of friction angle. Finally, the research concluded the possibility of using the results obtained from this study as a design charts to obtain the various retaining wall elements and different safety factors within the limits of studied parameters i.e, soil friction, height of retaining wall and surcharge load.