For the first time, organophosphate ester (OPE) content was studied in different types of surgical, self-filtering (KN95, FFP2, and FFP3) and reusable face masks used for COVID-19 prevention. OPEs were detected in all mask samples, although in highly variable amounts which ranged from 0.02 to a maximum of 27.7 µg/mask, with the highest mean concentrations obtained for KN95 masks (11.6 µg/mask) and the lowest for surgical masks (0.24 µg/mask). Twelve out of 16 tested analytes were detected, with TEP, TPHP, TNBP, TEHP and TClPP being the most common OPEs as well as present at the highest concentrations. The non-carcinogenic and carcinogenic risks of OPE inhalation were calculated as being always several orders of magnitude lower than threshold levels, indicating that the use of face masks is safe with regard to OPE contamination. However, given the wide range of OPEs observed in different masks, it can be concluded that some masks (e.g. reusable) are less OPE-contaminated than others (e.g. KN95). With regard to environmental pollution, the disposal of billions of face masks is adding to the already substantial levels of microplastics and associated toxic additives worldwide, an impact that is lessened by use of reusable masks, which also have the lowest economic cost per user. However, in situations of relatively high risk of viral inhalation, such as poorly ventilated indoor public spaces, we recommend the use of FFP2 masks.
17 January 2023 in Science of The Total Environment
We revisit current understanding of the chemical complexity of different kinds of particulate vulcanised elastomers widely used in playgrounds and sports fields, adding new data on trace element and organophosphate ester contents of used tyre and EDPM crumb rubber. Enrichments in elements such as Zn, S, Co, Bi and Nd relate to the vulcanised mixtures created during manufacture. Zinc concentrations vary across an order of magnitude, being highest in our used tyre particulate samples (up to 2.4 %). In contrast, other trace element variations are due to coloured pigments causing increases in Cu and Zr (blue), Cr (green), and Fe and Sn (red and yellow) concentrations. The use of pale fillers such as CaCO3 and clay minerals (rather than carbon black) strongly influences Ca and Al concentrations, which are much higher in the coloured EPDM than in black used tyre crumb rubber. Representatives from all three of the main organophosphate ester (OPE) groups, namely chlorinated (e.g. TCEP, TCIPP, TDCPP), alkyl (e.g. TEHP, TEP, TNBP, TBOEP) and aryl (e.g. TPHP, EHDPP, TCP) were identified, confirming how these chemicals are commonly used in modern rubber compounding as flame retardants and plasticisers. Elevated concentrations of TEHP (up to 117 μg/g) in coloured-coated used tyre turf infill crumb rubbers were traced to the coating rather than the crumb rubber itself. The presence and weathering behaviour of OPEs in recreational crumb rubber materials deserve closer investigation. The ecological "onehealth" impact of potentially toxic substances present in recreational crumb rubbers will depend on if and how they are released during play and sports activities, maintenance procedures, and natural weathering. We argue that detailed chemical data on these materials should be available to buyers, as manufacturers strive to reduce ecotoxin content as part of the quest towards sustainable use and recycling of vulcanised elastomers.
Aluminium is the most common substrate in studies using impactors for the measurement of the number or the weight of size-segregated atmospheric particulate matter (PM), as its characteristics perfectly fit impactor requirements. However, its use is not recommended by manufacturers when one of the purposes of the study is the determination of the metal content in the sample. The aim of this work was to develop an efficient analytical procedure for the removal and acid digestion of PM samples collected on aluminium foils by a cascade impactor to perform the determination of metals. The possibility of performing the trace metal analysis of PM samples collected using aluminium foils is of great importance, as it allows the determination of an accurate size distribution and the elemental composition of the PM collected on each impactor stage. Two procedures were optimised by using different digestion and analysis techniques. Both procedures were then applied to the two halves of several Dekati low-pressure impactor (DLPI) samples, and the results were critically compared. The two procedures proved to be effective in the determination of extremely low concentrations of a large suite of analytes in different size fractions of PM emitted by a brake system.