Raju Patel

Dr. Raju Patel

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 July 2019 in Turkish Journal of Electrical Engineering and Computer Sciences
Verified
Journal Article
Open access
STSuman Lata Tripathi
Suman Lata Tripathi
Raju PatelRaju Patel
Raju Patel
VAVimal Kumar Agrawal
Vimal Kumar Agrawal

10 October 2018 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
AJArun Kishor Johar
Arun Kishor Johar
Raju PatelRaju Patel
Raju Patel
CPC. Periasamy
C. Periasamy
AAAjay Agarwal
Ajay Agarwal
DBDharmendar Boolchandani
Dharmendar Boolchandani
This paper represents the design and FEM modeling of solidly mounted film bulk acoustic resonator (SMFBAR) gas sensor, based on ZnO, for volatile organic gas detection. The effect of sensitive polyisobutylene(PIB) layer coating on mass sensitivity has been analyzed along with optimization of the layer thickness. The proposed structure shows good quality factorof 758,at resonance condition, and a coupling coefficient of 7.36% for the piezoelectric layer with 2 μm thickness. SMFBAR sensor was tested for detection of various gases such as, Tetrachloroethane(PCE), Trichloroethylene (TCE), Trichloromethane(TCM) and chloromethane (CM), with PIB layer as the sensing element. Enhanced sensitivity of 21kHz/ppm has been achieved for detection of Tetrachloroethane (PCE) gas. FEM Modeling has been done on COMSOL Multiphysics software and a resonant frequency of 1.38 GHz has been observed for ideal environment. The sensor was tested for various gas concentrations ranging from 100 to 1000 ppm of volatile organic gases.

14 September 2020 in Electronics Letters
Verified
Journal Article
Open access
PDF file
Raju PatelRaju Patel
Raju Patel
MAM.S. Adhikari
M.S. Adhikari
DBD. Boolchandani
D. Boolchandani
In this Letter, an active area optimisation technique to improve the performance parameters of the film bulk acoustic resonator (FBAR) is proposed. The active area of the back trench membrane‐based FBAR is optimised to remove the spurious modes, higher harmonic modes, and to confine the acoustic signal at its central part during the resonance. The effect of thickness variation of SiO 2 layer on the performance parameters was studied using finite‐element analysis (FEA) simulation. The SiO 2 film, on silicon substrate, was used as the support layer and zinc oxide was used as the piezoelectric film for the resonator. The authors have successfully demonstrated the FBAR through FEA for an optimised active area of 320 × 320 µm 2 , series resonance frequency ( f s ) 1.249 GHz, and parallel resonance frequency ( f p ) 1.273 GHz with an effective electromechanical coupling coefficient of 4.65%.

27 July 2018 in IEEE Sensors Journal
Verified
Journal Article
Closed access
VAVimal Kumar Agrawal
Vimal Kumar Agrawal
Raju PatelRaju Patel
Raju Patel
DBDharmendar Boolchandani
Dharmendar Boolchandani
KRKamaljit Rangra
Kamaljit Rangra
In this paper fabrication of a rectangular paddle micro-cantilever based wind speed sensor along with its analytical model has been presented. The analytical model uses the closed form solution to the bending stress caused by static deflection. Simulations of the device were done using Finite Element Analysis (FEA). The simulation, analytical and experimental results have been compared for a better insight into the sensor behavior. Piezo-resistive deflection detection mechanism has been utilized to measure the wind speed. The experimental results show that fabricated sensor can detect wind speed up to 29 ms–1 and has a sensitivity of 0.071 mV/ms–1 –V .

1 October 2019 in AEU - International Journal of Electronics and Communications
Verified
Journal Article
Closed access
MAManoj Singh Adhikari
Manoj Singh Adhikari
Raju PatelRaju Patel
Raju Patel
YSYashvir Singh
Yashvir Singh

1 April 2017 in Journal of Micro/Nanolithography, MEMS, and MOEMS
Verified
Journal Article
Closed access
PDF file
Raju PatelRaju Patel
Raju Patel
MPManishkumar Patel
Manishkumar Patel
DBDharmendar Boolchandani
Dharmendar Boolchandani
KRKamal J. Rangra
Kamal J. Rangra
The application of a film bulk acoustic resonator (FBAR) as a gas sensor is presented here. Zinc Oxide is used as a piezoelectric (PZE) material for the resonator and a Bragg reflector is made of Molybdenum and Silicon dioxide in proposed Solidly Mounted FBAR. The structure offers a high quality factor of 1209 at the resonance and shows a coupling coefficient of 7.51% for the 0.7-μm-thick PZE layer. To make it capable of working as a gas sensor, an additional sensitive layer for adsorption is used. A 0.51-μm-thin film of polymer-sensitive layer (polyisobutylene, PIB) is used on the top electrode. The adsorption of CH2Cl2 (dichloromethane, DCM) prompts the change in density of the PIB layer, which causes the change in resonance frequency of the FBAR. The simulation results have shown the sensitivity of 450  Hz/ppm for gas sensing for the above-mentioned structure. The sensitivity of the sensor depends on the characteristic frequencies of the device, which are further the function of the thickness of the resonating structure. No involvement of a harsh etching process in fabrication, in addition to immense sensitivity and quality factor, makes this sensor relevant for DCM sensing.