Kamaljit Rangra

Kamaljit Rangra

Auto-generated profile, based on publicly available information

Kamaljit Rangra

Department of Electrical Engineering, Indian Institute of Technology Jodhpur, Jodhpur, Rajasthan, India

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2019 in Superlattices and Microstructures
Verified
Journal Article
Closed access
MAMahesh Angira
Mahesh Angira
DBDeepak Bansal
Deepak Bansal
PKPrem Kumar
Prem Kumar
KMKhusbu Mehta
Khusbu Mehta
KRKamaljit Rangra
Kamaljit Rangra

1 March 2016 in Engineering Science and Technology, an International Journal
Verified
Journal Article
Open access
MAMahesh Angira
Mahesh Angira
KRKamalJit Rangra
KamalJit Rangra
This paper presents a new type of capacitive shunt RF-MEMS switch. In the proposed design, float metal concept is utilized to reduce the RF overlap area between the movable structure and central conductor of CPW for improving the insertion loss of the device. This has been achieved without affecting the down-state response. Further, float metal also makes the down-state behavior predictable in terms of resonant frequency. For reducing the pull-in voltage, the switch is implemented with cantilever type of structure on either side of the transmission line. This structure also has the capability to inductively tune the isolation optimum value to the different bands and thus can be used in the reconfigurable RF systems. The device shows an insertion loss less than 0.10 dB, a return loss below 36.80 dB up to 25 GHz as compared to 1.00 dB insertion, 7.67 dB return loss for the conventional switch. In the OFF state, proposed device shows two isolation peaks i.e. 48.80 dB at 4.5 GHz and 54.56 dB at 9.7 GHz, when either or both cantilevers are electro-statically actuated to the down-state position respectively. The conventional device has a single isolation peak in the X-band. In addition, improvement of around 3 times in the bandwidth has also been achieved. The designed switch can be used at device and sub-system level for the future multi-band communication applications

27 July 2018 in IEEE Sensors Journal
Verified
Journal Article
Closed access
VAVimal Kumar Agrawal
Vimal Kumar Agrawal
Raju PatelRaju Patel
Raju Patel
DBDharmendar Boolchandani
Dharmendar Boolchandani
KRKamaljit Rangra
Kamaljit Rangra
In this paper fabrication of a rectangular paddle micro-cantilever based wind speed sensor along with its analytical model has been presented. The analytical model uses the closed form solution to the bending stress caused by static deflection. Simulations of the device were done using Finite Element Analysis (FEA). The simulation, analytical and experimental results have been compared for a better insight into the sensor behavior. Piezo-resistive deflection detection mechanism has been utilized to measure the wind speed. The experimental results show that fabricated sensor can detect wind speed up to 29 ms–1 and has a sensitivity of 0.071 mV/ms–1 –V .

1 November 2024 in Microchemical Journal
Verified
Journal Article
Closed access
VCVandana Kumari Chalka
Vandana Kumari Chalka
KMKhushi Maheshwari
Khushi Maheshwari
MCMeenu Chhabra
Meenu Chhabra
KRKamaljit Rangra
Kamaljit Rangra
SDSaakshi Dhanekar
Saakshi Dhanekar

1 March 2018 in Infrared Physics & Technology
Verified
Journal Article
Closed access
SGSurender P. Gaur
Surender P. Gaur
PKPrateek Kothari
Prateek Kothari
KRKamaljit Rangra
Kamaljit Rangra
DKDinesh Kumar
Dinesh Kumar

31 March 2005
Verified
Conference Paper
Closed access
KRK.J. Rangra
K.J. Rangra
FGFlavio Giacomozzi
Flavio Giacomozzi
BMB. Margesin
B. Margesin
Leandro LorenzelliLeandro Lorenzelli
Leandro Lorenzelli
VMViviana Mulloni
Viviana Mulloni
GSG. Soncini
G. Soncini