Single crystalline samples with starting compositions Fe x Te 0.60 Se 0.40 (x = 0.970, 0.985, 1, 1.015 and 1.030) have been grown using the self-flux method to study the effect of Fe variation (x) on the structural and superconducting properties of the grown single crystalline samples. All the grown samples are found superconducting and among all, the FeTe 0.60 Se 0.40 (x = 1) sample shows the highest superconducting transition temperature (T C ). For the samples with x other than 1, a decrease in the superconducting properties, such as T C , activation energy (U 0 ) and upper critical field (H C2 (0)), has been observed. The thermal activation energy (TAE) of the flux flow has been calculated using the conventional method and modified thermally activated flux flow (TAFF) model. The values of U 0 (H) show transition from the single vortex pinning regime to the collective vortex pinning regime at 2T. Also, the presence of planer defects has been estimated via both models. Furthermore, the modified TAFF model suggests three dimentional (3D) behaviour for all the grown single crystals. The vortex phase diagrams have been established by analysing the magnetoresistance data. The analysis reveals the transitions from unpinned to pinned vortex liquid region and also from the pinned vortex liquid state to vortex glass state. In the vortex phase diagram, below the critical temperature (T*), the critical exponent (s) is in a good agreement with the ‘q’ values for the 3D behaviour of vortex states for all the grown samples.
This study analyzes the calculation of the critical current density Jc,mag by means of Bean’s critical state model, using the equation formulated by Gyorgy et al. and other similar equations derived from it reported in the literature. While estimations of Jc,mag using Bean’s model are widely performed, improper use of different equations with different magnetic units and pre-factors leads to confusion and to significant errors in the reported values of Jc,mag. In this work, a SINGLE general equation is proposed for the calculation of Jc,mag for a rectangular parallelepiped sample in perpendicular field using Bean’s critical state model, underlying how the simple conversion of magnetic units can lead to a Jc,mag in the desired units, without the need to introduce any other correction or use other specific equations depending on the units of Jc,mag. In this equation, the numerical pre-factor is dimensionless, independent of the unit system used. A comparison between the expression reported in the literature is done, showing how they can lead to different results depending on the used units, and that these results can be at least one order of magnitude different from the correct results obtained with the general equation proposed in this work. This resolves all ambiguities and aligns with the correct dimensional analysis, eliminates discrepancies in the calculated Jc,mag, and will avoid further propagation of errors in the literature.
The heavy fermion ferromagnet CeRh6Ge4 is the first example of a clean stoichiometric system where the ferromagnetic transition can be continuously suppressed by hydrostatic pressure to a quantum critical point. In order to reveal the outcome when the magnetic lattice of CeRh6Ge4 is diluted with non-magnetic atoms, this study reports comprehensive measurements of the physical properties of both single crystal and polycrystalline samples of LaxCe1–xRh6Ge4. With increasing x, the Curie temperature decreases, and no transition is observed for x > 0.25, while the system evolves from exhibiting coherent Kondo lattice behaviors at low x to the Kondo impurity scenario at large x. Moreover, non-Fermi liquid behavior is observed over a wide doping range, which agrees well with the disordered Kondo model for 0.52 ≤ x ≤ 0.66, while strange metal behavior is revealed in the vicinity of xc = 0.26.
Superconducting thin films of two thicknesses have been fabricated on (100) oriented SrTiO3 (STO) substrates using the target of composition Fe1.05Te0.50Se0.50 by pulsed laser deposition technique. The structural and transport properties of the fabricated thin films have been investigated and the results indicate the enhancement in the superconducting properties with increasing thickness of the thin films. The onset of the superconducting transition temperature of the grown thin films of thicknesses ∼78 nm and ∼177 nm are ∼12.10 and 12.62 K at 0 T magnetic field, respectively. To estimate the upper critical fields HC2(0), thermally activated energy (TAE) and vortex phase diagram, the magnetoresistance measurements have been performed in the magnetic field range of 0 - 8 T. HC2(0) have been calculated by Ginzburg Landau (GL) theory and Werthamer-Helfand-Hohenberg model by taking the criterion of 90%, 50% and 10% of normal state resistivity and the corresponding GL coherence lengths have also been calculated. In the present work, the TAE has been estimated by conventional Arrhenius relation and modified thermally activated flux flow (TAFF) theory. The power law dependence of TAE, shows prominently the possible planer defects in the system. From the modified TAFF model, the values of fitting parameter ‘q’ suggests the 3 dimensional behaviour of the vortices for both the grown thin films. The vortex phase diagram study reveals the transition from the vortex liquid to vortex glass state.
In the last decade, the self-field critical current density Jc(s.f.) in Type-II superconductors has been considered fundamentally limited by a Silsbee-like criterion of Jc(s.f.) = Hc1/λ. We show that this universal limit to self-field critical current density Jc(s.f.) is not universally valid. We present several examples for this in YBa2Cu3O7−δ-type and REBa2Cu3O7−δ thin films and one for Nb thin films and show that calculated Jc(s.f.) using the Silsbee-like criterion using thermodynamic parameters has been substantially exceeded experimentally. We also show that Jc(s.f.) can be significantly improved by incorporation of artificial pinning centers (APCs), further implying that no such universal limit to Jc(s.f.) can exist because such an upper bound, Jc(s.f.) would have to be independent of APCs. These findings call for a revision of the accepted understanding of current-carrying limits in Type-II superconductors and reveal substantial potential for improving Jc in REBCO-based coated conductors through optimization of APCs for large-scale applications, including commercial nuclear fusion.
This study analyzes the calculation of the critical current density Jc,mag by means of the Bean's critical state model, using the equation formulated by Gyorgy et al. and other similar equations derived from Gyorgy et al. reported in literature. While estimations of Jc,mag using the Bean's model are widely done, improper use of different equations with different magnetic units and pre-factors, leads to confusion and to significant errors in the reported values of Jc,mag. We propose a SINGLE general equation for calculation of Jc,mag for a rectangular parallelepiped sample in perpendicular field using the Bean's critical state model, underlying how the simple conversion of magnetic units can lead to a Jc,mag in the desired units, without the need to introduce any other correction or use other specific equations depending on the units of Jc,mag. This resolves all ambiguities and aligns with the correct dimensional analysis, eliminates discrepancies in the calculated Jc,mag and will avoid further propagation of errors in the literature. In this equation, the numerical pre-factor is dimensionless, independent of the unit system used.