CuO was synthesized by employing the facile chemical precipitation technique to vary the concentrations of Cu(NO3)2 in a range from 0.001 to 0.1 M. This was carried out in order to find the concentration of Cu(NO3)2 that results in optimal electrochemical performance in CuO as an anode electrode material for lithium-ion batteries. Among the investigated concentrations, the 0.03 M Cu(NO3)2 showed the best electrochemical performance. Of the synthesized materials, the scanning electron microscopic (SEM) analysis revealed the existence of a sponge-like morphology. X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), synchrotron X-ray diffraction (SXRD) and Raman spectrum confirmed the formation of a required CuO phase. The electron density distribution on the crystalline structure of the synthesized CuO indicates the existence of the highest distribution of electrons around Cu atoms, with enhanced productivity of the conversion mechanism during the cycling process. Further, this study shows that the electronic interfacial properties of Cu/CuO could be improved by optimizing the amount of acetylene black used for the electrode fabrication, with 20 wt% being the optimum value. The electrodes fabricated with the synthesized sponge-like microstructured CuO as the active material exhibited a high initial specific discharge capacity of 3371.9 mA h g−1 and resulted in a specific discharge capacity of 442.9 mA h g−1 (Coulombic efficiency of 97.4%) after 50 cycles, at a rate of 0.2 C. Moreover, the specific discharge capacity reported at the rate of 1.0 C was 217.6 mA h g−1 with a significantly high Coulombic efficiency of about 98.0% after 50 cycles. Altogether, this study reveals the high potentiality of using sponge-like microstructured CuO as a high-performance anode electrode material for LIBs.
Improving the performance of TiO2 photoanodes via the inclusion of metal particles on the electrode surface could provide significant advantages for the development of dye-sensitized solar cells (DSSCs). We studied a TiO2/Cu film electrode prepared by electrodepositing Cu particles on a TiO2 film on an indium-doped tin oxide (ITO) substrate. Cu particles were electrodeposited on a TiO2 electrode at −700 mV vs. a Ag/AgCl electrode in an acetate bath, with the pH adjusted between 6.3 and 7.7 in 0.2 increments to optimize the deposition conditions. TiO2/Cu thin-film electrodes were tested as a photo anode in a natural DSSC consisting of a carbon counter electrode, Vitis vinifera dye, and a KI/I2-based electrolyte. Film characterization was performed using hard X-ray photoelectron spectroscopy (HAXPES), grazing incidence X-ray diffraction (GIXD), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, electrochemical impedance spectroscopy (EIS), ultraviolet–visible spectroscopy (UV–Vis), and photocurrent density–voltage (J–V) measurements. DSSCs with Cu particles containing TiO2 electrodes prepared using an acetate bath of pH 7.3 resulted in a 370% improvement in efficiency compared to the DSSCs without Cu particles. Thus, this study revealed that incorporating Cu particles into the surface of the TiO2 electrode enhances the photovoltaic performance of DSSCs.
Dissolved oxygen (DO) is a crucial parameter in water quality monitoring because it directly affects the health of aquatic ecosystems. This study explored electrodeposited Cu2O thin-film semiconductors for DO sensing. Cu2O was chosen for its low cost, eco-friendliness, and non-toxic nature. Cu2O films were electrodeposited on titanium (Ti) substrates using an acetate bath (0.1 M sodium acetate and 0.01 M cupric acetate) at −200 mV versus Ag/AgCl for 30 min, with a bath temperature of 55 °C, stirred at 50 rpm. The bath pH was systematically adjusted from 5.8 to 6.8 in 0.2 steps using NaOH and Acetic acid. A range of analyses including synchrotron X-ray diffraction (SXRD), scanning electron microscopy (SEM), surface wettability, capacitance–voltage (C-V), Raman spectroscopy, Fourier-transform infrared (FTIR) spectrum, and Electrochemical Impedance Spectroscopy (EIS) was performed to assess their properties and sensing performance. The results showed that Cu2O films deposited at pH 6.4 exhibited optimal performance for DO sensing, with a strong linear response, marking this pH, deposition time, and temperature as ideal for creating effective DO sensors. This study introduces a novel, cost-effective approach to dissolved oxygen sensing using electrodeposited n-Cu2O thin-film semiconductors, marking the first application of this material in such sensors and showcasing its potential for scalable and environmentally sustainable sensing technologies.
18 August 2026 in Journal of Physics and Chemistry of Solids