Over the years, cultivation using sustainable tillage practices has gained significant importance, but the impact of tillage on soil water infiltration is still a concern for landowners due to the possible effects on crop yield. This study investigates the impact of different tillage managements on the infiltration rate of sandy clay loam soil under a semiarid environment. Field experiments were conducted in Chott Mariem Sousse, Tunisia. The tillage practices consisted of three treatments, including a tine cultivator (TC, 16 cm), moldboard plows (MP, 36 cm) and no-tillage (NT). Three infiltration models, Kostiakov, Philip and Horton, were applied to adjust the observed data and evaluate the infiltration characteristics of the studied soils. Comparison criteria, including the coefficient of determination (R²), along with the root mean square error (RMSE) and mean absolute error (MAE), were used to investigate the best-fit model. The results showed that moldboard plowing enhanced soil infiltration capacity relative to tine cultivation and no-tillage treatments. The mean saturated hydraulic conductivity was highest under MP, while it was lowest in NT, with 33.4% and 34.1% reduction compared to TC and MP, respectively. Based on the obtained results, Philip’s model showed better results with observed infiltration due to a higher R² (0.981, 0.973 and 0.967), lower RMSE (3.36, 9.04 and 9.21) and lower MAE (1.46, 3.53 and 3.72) recorded, respectively, for NT, MP and TC. Horton’s model had a low regression coefficient between observed and predicted values. It was suggested that the Philip two-term model can adequately describe the infiltration process in the study area.

Context: Shifting agricultural operations to more sustainable management practices is needed in the face of a changing climate. Aims: In this study, the short-term effects of three tillage systems (no tillage, minimum tillage and conventional tillage) on a wide selection of soil properties in a semi-arid agrosystem of eastern Tunisia were assessed. Methods: The studied soil properties included saturation percentage, bulk density, penetration resistance, mean weight diameter, electric conductivity, soil reaction, soil organic matter, carbonates, available phosphorus and exchangeable potassium. The impacts of tillage systems on soil quality indices (SQI) developed based on the total set of properties (SQI-T), or a minimum set (SQI-M) selected through principal component analysis, were also investigated. Key results: Relative to conventional tillage, no tillage increased bulk density, penetration resistance and electrical conductivity, whereas minimum tillage affected only saturation percentage and pH. No tillage and minimum tillage did not enhance soil quality relative to conventional tillage. The SQI-T and SQI-M were highly correlated (r = 0.93) to each other suggesting that the outcomes of the two indices are comparable. Principal component analysis efficiently selected the most influential indicators of the effects of tillage systems on soil quality. Conclusions and implications: Farmers in the study region are encouraged to consider minimum tillage during the early years of transition from standard to no tillage systems to avoid rapid decline in soil quality and consequent yield loss.

Introduction: Drought stress is one of the most devastating environmental stressors, especially in the arid and semi-arid regions of the world. Considering the major constraints that drought stress poses to crop production and the consequent yield losses in food crops, breeding for climate-resilient crops is an efficient means to mitigate stress conditions. Materials and methods: This study aimed at evaluating the response of four squash (Cucurbita maxima Duchesne) landraces to drought stress at germination and at plant stage. Drought stress was induced by different concentrations of D-mannitol (-0.24, -0.47 and -0.73 MPa). The tested parameters at germination stage included germination percentage, seedling vigor index, seed water absorbance and seedling growth potential. At the plant stage, leaf chlorophyll and carotenoids content, chlorophyll fluorescence, evapotranspiration, photosynthesis activity and several biomarkers, namely malondialdehyde, proline, total phenols content, total flavonoids content and DPPH radical scavenging activity were evaluated in both roots and leaves.Results and discussion: Our results indicate a magnitude of drought stress effects reflected via repression of germination and seedling growth as well as adjustments in physiological functions at later growth stages, in a genotype depended manner. Among landraces, "751" and "746" showed better performance, as evidenced by higher seed germination and seedling growth potential even at high stress levels (-0.47 and - 0.73 MPa), whereas "747" was the most sensitive landrace to drought stress at both tested stages. In conclusion, our findings highlight the importance of squash landraces selection for the identification of elite genotypes with increased tolerance to drought stress.

In recent years, the investment in the wind energy sector has increased in the context of producing green electricity and saving the environment. The installation of small wind turbines (SWTs) represents an actual strategy for meeting energy needs for off-grid systems and certain specialized applications. SWTs are more expensive per kilowatt installed as compared to large-scale wind turbines. Therefore, the main objective of this study is to produce an economical technology for the wind power market offering low-cost SWTs. The idea consists of considering a simple structure of the wind turbine using direct-drive permanent magnet synchronous generator (DDPMSG). DDPMSGs are the most useful machines in the wind energy field thanks to several advantages, such as elimination of noise and maintenance cost due to suppression of the gearbox and absence of the rotor circuit excitation barriers by the presence of the permanent magnets (PMs). Their major downside is the high cost of active materials, especially the PMs. Thus, the improvement of the generator design is treated as being the main component of the considered chain to assure active materials’ mass and cost reduction. The methodology studied aims to explain the approach of the design integrated by optimization of the considered system. It is based on the elaboration of analytical models to find a feasible structure for the system, taking into account the multi-disciplinary analysis. The relevance of these models is validated by the finite element method using 2D MATLAB-FEMM simulation. The models are integrated to elaborate the optimization problem based on a genetic algorithm to improve the cost of the proposed generator by minimizing the mass of its active constructive materials. As an outcome, an optimal solution is offered for the wind generators market, providing a 16% cost reduction.

In agricultural systems, soil carbon dioxide emissions and physical properties are thought to depend largely on management practices. This field study was carried out in a semi-arid region of eastern Tunisia to evaluate the effects of tillage management on soil carbon dioxide emissions and related physical properties; bulk density (BD), penetration resistance (PR), total porosity (TP) and air-filled porosity (AFP). Tillage management treatments included plowing with a moldboard plow or a disk plow to different depths, described here as shallow (10 cm), medium (15 cm) and deep (25 cm). No-tillage was also considered as a control plot. Correlation analysis was used to explore how soil carbon dioxide emissions (CO2) were related to the other studied properties. The results showed higher carbon dioxide (CO2) emissions (p < .05) from tilled soil compared to no-till (NT), regardless of the tillage management. No significant differences in carbon dioxide (CO2) emissions were found between moldboard and disk plow tillage at the same tillage depth. Soil carbon dioxide release was the highest after deep tillage (moldboard = 0.101 t ha−1 and disk plow = 0.107 t ha−1) suggesting that deeper tillage to 25 cm promoted higher carbon dioxide (CO2) emissions. Significant differences with tillage were observed in bulk density (BD) and penetration resistance (PR) compared to no-tillage. Correlations of carbon dioxide emissions to soil physical properties across all the tillage treatments indicated significant negative relationships between carbon dioxide (CO2) emissions and soil bulk density (BD) and penetration resistance (PR) and significant positive relationships between carbon dioxide (CO2) and total porosity (TP) and air-filled porosity (WFP) suggesting that these soil attributes are important controlling factors of carbon dioxide (CO2) emissions.