The main objective of this research is to investigate the impact of the tendon profile layout on the shear strength of unbonded post-tensioned prestressed concrete bridge I-girders. This study involves an experimental investigation where ten unbonded post-tensioned bridge girders are cast and subjected to four-point loads. The focus of the investigation is on the effect of different tendon profile layouts, including trapezoidal, parabolic, and harped shapes. The experimental results reveal that the shear behavior of the specimens progresses through three distinct stages: the elastic stage, the elastic–plastic stage, and the plastic stage, with all specimens ultimately failing due to shear. The results show that tendon profiles with higher eccentricity at the end of the beams (80 mm above the neutral axis) had the highest ultimate load capacity for each tendon profile shape, coupled with the largest deflection. Conversely, profiles with lower eccentricity (80 mm below the neutral axis) demonstrated the lower ultimate load capacity for each tendon profile shape and minimal deflection. Among the various tendon profile layouts that were tested, the specimen with the harped tendon profile (GF-1 HA) showed the highest ultimate load capacity, with an increasing rate of 17.52% in ultimate load and a 45.55% increase in ultimate deflection compared to the control beam (GF-1 ST) with a straight tendon profile. On the other hand, the harped tendon profile specimen (GF-1 HA) exhibited the lowest deflection among the various tendon profile shapes with an increasing rate of 5.7% in ultimate load deflection in comparison with the control beam (GF-1 ST) with a straight tendon profile. These improvements in stiffness, load capacity, and deflection are attributed to enhanced resistance, particularly at the supports. Consequently, the optimized tendon layouts offer an increase in the overall structural efficiency, leading to potential cost savings in bridge girder production.
The primary objective of this research is to investigate the impact of tendon profile layout on the shear strength of unbonded, post-tensioned prestressed concrete bridge I-girders. This study involves an experimental investigation where ten un-bonded, post-tensioned bridge girders are cast and subjected to four-point loads. The focus of the investigation is on the effect of different tendon profile layouts, including trapezoidal, parabolic, and harped shapes. The experimental results reveal that the shear behavior of the specimens progresses through three distinct stages: the elastic stage, the elastic–plastic stage, and the plastic stage, with all specimens ultimately failing due to shear. The findings show that tendon profiles with an eccentricity at the end of the beam = -80mm (80 mm above the neutral axis) exhibited the highest ultimate load capacity, coupled with the largest deflection. Conversely, profiles with an eccentricity of = 80mm (80 mm below the neutral axis) demonstrated the lowest load capacity and minimal deflection. Among the various configurations tested, the specimen with the harped tendon profile (GF-1 HA) showed the highest ultimate load capacity. On the other hand, the trapezoidal tendon profile specimen (GF-2 TR) exhibited the lowest deflection. These improvements in stiffness, load capacity, and deflection are attributed to enhanced resistance, particularly at the supports. Consequently, the optimized tendon layouts offer a reduction in deflection and an increase in the overall structural efficiency, leading to potential cost savings in bridge girder production.
The main objective of this research is to evaluate the optimal design of the tendon profile layout and to examine the effect of the tendon profile layout on the flexural strength of unbounded post-tensioned prestressed concrete bridge I-girders. In this study, the experimental investigation involved casting and testing ten unbounded post-tensioned bridge girders under a four point loads. The main variable studied was the tendon profile layout. The experimental results showed that the flexural behavior of tested specimens is divided into three stages: elastic stage, elastic-plastic stage and plastic stage and all specimens exhibit flexural failure. It can be concluded that for each tendon profiles layout (trapezoidal, parabolic, harped), the tendon profiles with eccentricity at end of beam (ee)=0, had maximum ultimate load capacity. It also can be concluded that specimen GF-9 HA (Harped Tendon Profile with ee = 0 mm) had maximum ultimate load capacity from all other specimens. These enhancement in specimens stiffness, ultimate loads capacities and deflections because of increasing resisting capacity , reducing stresses specially at support, reducing deflection, increasing resisting bending moment which lead to reducing the production cost of girder.
The main objective of this research is to evaluate the optimal design of the tendon profile layout and to examine the effect of the tendon profile layout on the flexural strength of unbonded, post-tensioned prestressed concrete bridge I-girders. In this study, the experimental investigation involved casting and testing ten unbonded, post-tensioned bridge girders under four-point loads. The main variable studied was the tendon profile layout. The experimental results showed that the flexural behavior of the tested specimens is divided into three stages, including the elastic stage, elastic–plastic stage, and plastic stage, and all specimens exhibited flexural failure. It can be concluded that for each tendon profile layout (trapezoidal, parabolic, harped), the tendon profile with eccentricity at the end of the beam (ee) = 0 had the maximum ultimate load capacity. It also can be concluded that specimen GF-2 HA (harped tendon profile with ee = 0 mm) had the maximum ultimate load capacity among all of the specimens. These enhancements in specimen stiffness, ultimate load capacities, and deflections are due to an increase in resisting capacity, a reduction in stresses, especially at the supports, a decrease in deflection, and an increase in the resisting bending moment, which lead to a reduction in the production cost of the girder.