Studies using starch to produce biodegradable materials have proved attractive due to its availability and low cost in relation to commercial biodegradable polymers, such as poly (lactic acid) and others. Starch-based materials do not have adequate mechanical properties for production and use on a commercial scale, requiring mixtures (blends) with other biodegradable polymers to improve these properties. However, these blends need compatibilizers due to the immiscibility between the starch and the polymer. The present work aimed to study the effect of different compatibilizers (3-(trimethoxysilyl) propyl methacrylate, citric acid, and maleic anhydride) on the functional properties of biodegradable starch and poly (lactic acid) (PLA) materials produced by extrusion and thermoplastic injection. Citric acid was considered the best compatibilizer for these materials because it improved the processability, and the materials presented properties suitable for applications where good mechanical resistance is required. In addition, the materials containing citric acid and maleic anhydride were more uniform from the morphological point of view.
A biodegradable polymer packaging system for ‘Benitaka’ table grapes (Vitis vinifera L.) was developed to inhibit the development of gray mold during refrigerated storage. The system consisted of packages and sachets containing Na2S2O5 to release sulfur dioxide (SO2), both produced with biodegradable films of starch, glycerol, and poly (adipate co-butylene terephthalate) (PBAT) produced via blown extrusion. The films were characterized in terms of thickness, density, mass loss in water, water vapor permeability, sorption isotherms, and mechanical properties. The table grapes were packed with biodegradable plastic bags containing SO2-releasing sachets inside. The experimental design was completely randomized, with four repetitions and five treatments: (a) control, without sachet containing Na2S2O5 and SiO2; (b) 2 g of Na2S2O5 + 2 g of SiO2; (c) 4 g of Na2S2O5 + 1 g of SiO2; (d) 4 g of Na2S2O5 + 2 g of SiO2; and (e) 4 g of Na2S2O5 + 4 g of SiO2. The bunches were stored in a refrigerated chamber at 1 ± 1 °C and relative humidity above 90%. The treatments were evaluated 30 and 45 days after the beginning of refrigerated storage and 3 days at room temperature. The grapes were evaluated based on the incidence of gray mold, mass loss, stem browning, shattered berries, and berry bleaching. The data were subjected to the analysis of variance, and the means were compared using Tukey’s test at 5%. The biodegradable films had good processability during the production via blown extrusion, with good physical properties to be used in the packaging of grapes and the production of SO2-releasing sachets. The biodegradable polymer packaging system (biodegradable plastic bags + SO2-releasing sachets) inhibited the development of gray mold on ‘Benitaka’ table grapes for 45 days at 1 °C, preserving their quality, with low mass loss, few shattered berries, and rachis freshness.
Fossil-origin plastics have raised great concerns due to their non-biodegradable nature. Biodegradable polymers can be an alternative for these materials’, however they have higher cost. The use of agro-industrial waste in blends with biopolymers can provide cheaper materials’ with improved properties. This study aims to develop low-cost biodegradable materials by extrusion and thermoplastic injection using oat hulls, polybutylene succinate (PBS), and starch. Six formulations with different concentrations of oat hulls (0-56% w/w) were extruded in a single-screw extruder, and then the materials were produced by thermoplastic injection. The extrusion aligned the oat hull fibers, making the material dimensionally stable. The oat hulls enhanced stiffness and reduced material density compared to non-hull counterparts. Besides that, the oat hulls are a low-cost agro-industrial byproduct, and it was possible to produce biodegradable materials with up to 56% hulls and only 20% PBS. These biodegradable materials are environmentally friendly and non-toxic.
The increasing concern regarding the environmental impact of conventional plastics has intensified the search for sustainable alternatives. This study investigated the development and characterization of biocomposites produced from glue flour (GF), a wheat milling by-product, and poly(butylene succinate) (PBS) using injection molding. GF/PBS ratios of 100/0 (PBS0), 80/20 (PBS20), 70/30 (PBS30), and 60/40 (PBS40) (w/w) were evaluated in terms of physical, mechanical, and thermal properties. The results showed that increasing the PBS content significantly enhanced tensile strength from 1.36 MPa (PBS0) to 12.23 MPa (PBS40) and Young’s modulus from 0.12 MPa to 1.54 MPa. Water solubility decreased from 37.03% (PBS0) to 16.08% (PBS40), and linear shrinkage was reduced from 5.5% (PBS0) to around 2.0% (PBS40). Scanning electron microscopy (SEM) analysis revealed improved homogeneity and reduced granule visibility with higher PBS concentration. Fourier transform infrared spectroscopy (FTIR) spectra indicated intensified interactions between starch, proteins, and PBS as its content in the formulation increased. Thermal analysis revealed that biocomposites containing PBS exhibited well-defined melting (Tm ~115 °C) and crystallization (Tc ~80 °C) temperatures, indicating more consistent thermal behavior than the PBS-free sample. These findings suggest that GF/PBS biocomposites have strong potential as sustainable alternatives to conventional plastics, offering viable applications across various industrial sectors.
The utilization of biopolymers blended with agro-industrial residues or by-products holds promise due to the potential for cost reduction and improvement of material properties. In this study, our aim was to develop biodegradable polymeric blends using PBS, starch, and oat hulls via thermoplastic injection. Seven different formulations were analyzed [F0, F20, F40, F60, F80, F100, and PBS], and various analyses were performed. The mechanical properties revealed that pure PBS and F0 presented the highest tensile strength and elongation at break respectively. Pure PBS and F100 demonstrated the lowest density. SEM of materials containing oat hulls displayed cylindrical-shaped fibers, with significant agglomeration and alignment likely due to extrusion orientation. The results demonstrate the successful production of a novel material using thermoplastic starch, PBS, and oat hulls through thermoplastic injection. These materials exhibited good processability. This presents a promising avenue for the development of cheaper and biodegradable materials with good processability to be produced in large scale, as they are environment friendly.
Developing sustainable packaging materials has become a global priority in response to environmental concerns associated with conventional plastics. This study used a wheat flour byproduct (glue flour, GF) and poly(butylene adipate-co-terephthalate) (PBAT) to produce films via blown extrusion, incorporating rosemary extract (RE) at 2% (FRE2) and 4% (FRE4) (w/w). A control film (FCO) was formulated without RE. The physicochemical, thermal, mechanical, and biodegradation properties of the films were evaluated. FCO, FRE2, and FRE4 exhibited tensile strength (TS) values between 8.16 and 9.29 MPa and elongation at break (ELO) above 889%. Incorporating 4% RE decreased luminosity (91.38 to 80.89) and increased opacity (41.14 to 50.95%). A thermogravimetric analysis revealed a main degradation stage between 200 °C and 450 °C, with FRE2 showing the highest residual mass (~15% at 600 °C). Sorption isotherms indicated enhanced hydrophobicity with RE, thereby reducing the monolayer moisture content from 5.23% to 3.03%. Biodegradation tests revealed mass losses of 64%, 58%, and 66% for FCO, FRE2, and FRE4, respectively, after 180 days. These findings demonstrate that incorporating RE into GF/PBAT blends via blown extrusion is a promising strategy for developing biodegradable films with enhanced thermal behavior, mechanical integrity, and water resistance, contributing to the advancement of sustainable packaging materials.