Energy storage system (ESS) technology is still the logjam for the electric vehicle (EV) industry. Lithium-ion (Li-ion) batteries have attracted considerable attention in the EV industry owing to their high energy density, lifespan, nominal voltage, power density, and cost. In EVs, a smart battery management system (BMS) is one of the essential components; it not only measures the states of battery accurately, but also ensures safe operation and prolongs the battery life. The accurate estimation of the state of charge (SOC) of a Li-ion battery is a very challenging task because the Li-ion battery is a highly time variant, non-linear, and complex electrochemical system. This paper explains the workings of a Li-ion battery, provides the main features of a smart BMS, and comprehensively reviews its SOC estimation methods. These SOC estimation methods have been classified into four main categories depending on their nature. A critical explanation, including their merits, limitations, and their estimation errors from other studies, is provided. Some recommendations depending on the development of technology are suggested to improve the online estimation.

The energy storage system (ESS) is the main issue in traction applications, such as battery electric vehicles (BEVs). To alleviate the shortage of power density in BEVs, a hybrid energy storage system (HESS) can be used as an alternative ESS. HESS has the dynamic features of the battery and a supercapacitor (SC), and it requires an intelligent energy management system (EMS) to operate it effectively. In this study, a real-time EMS is proposed, which is comprised of a fuzzy logic controller-based low-pass filter and an adaptive proportional integrator-based charge controller. The proposed EMS intelligently distributes the required power from the battery and SC during acceleration. It allocates the braking energy to the SC on the basis of the state of charge. A simulation study was conducted for three standard drive cycles (New York City cycle, Artemis urban cycle, and New York composite cycle) using MATLAB Simulink. Comparative analysis of conventional and proposed EMSs was carried out. The results reveal that the proposed EMS reduced the stress, temperature, and power losses of the battery. The steady-state charging performance of the SC was 98%, 95%, and 96% for the mentioned drive cycles.

As the number of electric vehicles (EVs) significantly increases, the excessive charging demand of parked EVs in the charging station may incur an instability problem to the electricity network during peak hours. For the charging station to take a microgrid (MG) structure, an economical and energy-efficient power management scheme is required for the power provision of EVs while considering the local load demand of the MG. For these purposes, this study presents the power management scheme of interdependent MG and EV fleets aided by a novel EV charging/discharging scheduling algorithm. In this algorithm, the maximum amount of discharging power from parked EVs is determined based on the difference between local load demand and photovoltaic (PV) power production to alleviate imbalances occurred between them. For the power management of the MG with charging/discharging scheduling of parked EVs in the PV-based charging station, multi-objective optimization is performed to minimize the operating cost and grid dependency. In addition, the proposed scheme maximizes the utilization of EV charging/discharging while satisfying the charging requirements of parked EVs. Moreover, a more economical and energy-efficient PV-based charging station is established using the future trends of local load demand and PV power production predicted by a gated recurrent unit (GRU) network. With the proposed EV charging/discharging scheduling algorithm, the operating cost of PV-based charging station is decreased by 167.71% and 28.85% compared with the EV charging scheduling algorithm and the conventional EV charging/discharging scheduling algorithm, respectively. It is obvious that the economical and energy-efficient operation of PV-based charging station can be accomplished by applying the power management scheme with the proposed EV charging/discharging scheduling strategy.

The lithium-ion battery has high energy and power density, long life cycle, low toxicity, low discharge rate, more reliability, and better efficiency compared to other batteries. On the other hand, the issue of a reduction in charging time of the lithium-ion battery is still a bottleneck for the commercialization of electric vehicles (EVs). Therefore, an approach to charge lithium-ion batteries at a faster rate is needed. This paper proposes an efficient, real-time, fast-charging methodology of lithium-ion batteries. Fuzzy logic was adopted to drive the charging current trajectory. A temperature control unit was also implemented to evade the effects of fast charging on the aging mechanism. The proposed method of charging also protects the battery from overvoltage and overheating. Extensive testing and comprehensive analysis were conducted to examine the proposed charging technique. The results show that the proposed charging strategy favors a full battery recharging in 9.76% less time than the conventional constant-current–constant-voltage (CC/CV) method. The strategy charges the battery at a 99.26% state of charge (SOC) without significant degradation. The entire scheme was implemented in real time, using Arduino interfaced with MATLAB^TM Simulink. This decrease in charging time assists in the fast charging of cell phones and notebooks and in the large-scale deployment of EVs.

Online accurate estimation of remaining useful life (RUL) of lithium-ion batteries is a necessary feature of any smart battery management system (BMS). In this paper, a novel partial discharge data (PDD)-based support vector machine (SVM) model is proposed for RUL prediction. The proposed algorithm extracts the critical features from the voltage and temperature of PDD to train the SVM models. The classification and regression attributes of SVM are utilized to classify and predict accurate RUL. The different ranges of PDD were analyzed to find the optimal range for training the SVM model. The SVM model trained with optimal PDD features classifies the RUL into six different classes for gross estimation, and the support vector regression is used to estimate the accurate value of the last class. The classification and predictive performance of SVM model trained using the full discharge data and PDD are compared for publicly available data. Results show that the SVM classification and regression model trained with PDD features can accurately predict the RUL with low storage pressure on BMS. The PDD-based SVM model can be utilized for online RUL estimation in electric vehicles.