Commercially pure (c.p.) titanium grade IV with a bimodal microstructure is a promising material for biomedical implants. The influence of the processing parameters on the physical, microstructural, and mechanical properties was investigated. The bimodal microstructure was achieved from the blends of powder particles with different sizes, while the porous structure was obtained using the space-holder technique (50 vol.% of ammonium bicarbonate). Mechanically milled powders (10 and 20 h) were mixed in 50 wt.% or 75 wt.% with c.p. titanium. Four different mixtures of powders were precompacted via uniaxial cold pressing at 400 MPa. Then, the specimens were sintered at 750 °C via hot pressing in an argon gas atmosphere. The presence of a bimodal microstructure, comprised of small-grain regions separated by coarse-grain ones, was confirmed by optical and scanning electron microscopies. The samples with a bimodal microstructure exhibited an increase in the porosity compared with the commercially available pure Ti. In addition, the hardness was increased while the Young’s modulus was decreased in the specimens with 75 wt.% of the milled powders (20 h).
Titanium (Ti) and its alloys are used for biomedical applications because of their high resistance to corrosion, good strength-to-weight ratio, and high fatigue resistance. However, a problem that compromises the performance of the material is the mismatch between Young’s modulus of Ti and the bone, which brings about stress shielding. One strategy that has been investigated to reduce this difference is the manufacture of Ti-based foams, using powder metallurgy (PM) methods, such as the space-holder technique. However, in the uniaxial compaction, both non-uniform density distribution and mechanical properties remain because of the compaction method. This work studies the influence of compaction by adopting a floating-action die related to a single-action die (SAD), on the density of green and sintered Ti foams with porosities around 50 vol.% characterized by optical microscopy, ultrasound analysis, compression tests, and microhardness. The compaction process employing a floating-action die generates Ti foams with a higher density up to 10% with more control of the spacer particle added compared to the single-action die. Furthermore, compaction method has no relevant effect on microhardness and Young’s modulus, which allows getting better consolidated samples with elastic modules similar to those of human bone.
2 September 2025 in Journal of Materials Research and Technology
A systematic comparative study of the performance of multi-walled carbon nanotube (MWCNT) synthesis via chemical vapor deposition (CVD) was conducted. Special emphasis is placed on the roles of TiO₂ size and polymorphism as catalyst supports and on how these factors influence the dispersion of the metal nanoparticles and their catalytic behavior. We present three distinct catalytic systems, supported on rutile particles, anatase particles, and anatase nanoparticles, each of which supports dispersed Fe-Co nanoparticles anchored to its surface. In parallel, catalyst calcination and synthesis parameters, specifically temperature and reaction time, were systematically optimized to maximize carbon fixation efficiency. The comparative difference in carbon fixation yield is 383% for rutile/Fe–Co/MWCNT, 321% for anatase/Fe–Co/MWCNT, and 673% for nanocrystalline anatase/Fe–Co/MWCNT. These results indicate that the particle size of the TiO₂ catalyst support, the crystalline phase, and the experimental design for optimizing synthesis parameters all play a crucial role in the yield of carbon nanotube synthesis. This suggests that a simple impregnation method can be used to fabricate a TiO₂-supported metal catalyst and produce MWCNTs with high yield via CVD. This study reveals that catalyst engineering and design will pave the way for the synthesis of nanomaterials tailored to specific applications. The results position nanocrystalline TiO₂ as a highly efficient and innovative catalyst support for advanced MWCNT synthesis.
High entropy alloys (HEAs) are potential materials for biomedical applications due to their unique properties. Also, the use of functionally graded porous materials (FGPM) presents an interesting approach that could help to decrease the Young’s modulus while simultaneously mimicking highly hierarchical porosity of the bone structure. In this study, Field Assisted Sintering Technology/Spark Plasma Sintering (FAST/SPS) and space-holder techniques were used to determine the viability of its use for produce HEAs which exhibit radially graded porous structures from Ti, Nb, Ta, Hf and Mo powders, using NH4HCO3 as space-holder. Results have shown that the radially porous gradient was formed when sintering at 1450°C and 10 min, but the sintering necks were not sufficient to provide adequate mechanical properties and achieve the desired porosity levels. Hence, future studies have to be carried out to determine the adequate sintering parameters to achieve good diffusion between particles.