The influence of different concentrations (0.5, 1.0, and 2.0 wt.%) of Zinc Oxide (ZnO) filler on the dielectric properties of the cold-curing polyurethane (PU) resin is presented in this study. For this purpose, the direct DC conductivity and the broadband dielectric spectroscopy measurements were used to describe the changes in dielectric responses of PU/ZnO nanocomposites over the frequency and temperature range, respectively. It can be stated that, the 1.0 wt.% nanoparticles and lower caused a decrease in the real relative permittivity compared to the pure PU resin, while the higher concentration of nanoparticles for frequencies above 1 Hz had the opposite effect. The presence of nanoparticles in the polyurethane resin affected the segmental dynamics of the polymer chain and changed a charge distribution in the given system. These changes caused a shift of local relaxation peaks in the spectra of imaginary permittivity and dissipation factor of nanocomposites. It is suggested that the temperature-dependent transition of the electric properties in the nano-composite is closely associated with the -relaxation and intermediate dipolar effects (IDE).
The influence of various types of nanoparticle fillers with the same diameter of 20 nm were separately incorporated into a single component impregnating resin based on a polyesterimide (PEI) matrix and its subsequent changes in complex relative permittivity were studied. In this paper, nanoparticles of AlO and ZnO were dispersed into PEI (with 0.5 and 1 wt.%) to prepare nanocomposite polymer. Dielectric frequency spectroscopy was used to measure the dependence of the real and imaginary parts of complex relative permittivity within the frequency range of 1 mHz to 1 MHz at a temperature range from +20 °C to +120 °C. The presence of weight concentration of nanoparticles in the PEI resin has an impact on the segmental dynamics of the polymer chain and changed the charge distribution in the given system. The changes detected in the H NMR spectra confirm that dispersed nanoparticles in PEI lead to the formation of loose structures, which results in higher polymer chain mobility. A shift of the local relaxation peaks, corresponding to the -relaxation process, and higher mobility of the polymer chains in the spectra of imaginary permittivity of the investigated nanocomposites was observed.
This study presents the influence of various types of nanoparticle (NP) fillers incorporated into a polyurethane (PU) (VUKOL 022) matrix and its subsequent changes in complex permittivity. Two types of surface modification of SiO 2 fillers were investigated. The frequency dependence of the real and imaginary parts of complex permittivity was measured within the frequency range of 1 mHz to 1 MHz using the capacitance method. The 1 wt.% NPs in PU caused an increase (MgO, TiO 2 , n-SiO 2 , and f-SiO 2 ) or a decrease (d-SiO 2 ) in the real permittivity. The α-relaxation and intermediate dipolar effect were observed at the temperature dependence of the imaginary permittivity. The change in permittivity by various surface modifications of SiO 2 and other nanofillers was discussed based on the multi-core model. Moreover, the NPs caused a shift in the local maximum of the permittivity, which was a result of the interfacial polarisation and a charge multiplication of the α-relaxation process.
Recently, polyurethanes (PURs) have become a very promising group of materials with considerable utilization and innovation potential. This work presents a comprehensive analysis of the changes in material properties important for PUR applications in the electrical industry due to the incorporation of magnesium oxide (MgO) nanoparticles at different weight ratios. From the results of the investigations carried out, it is evident that the incorporation of MgO improves the volume (by up to +0.5 order of magnitude) and surface (+1 order of magnitude) resistivities, reduces the dielectric losses at higher temperatures (−62%), improves the thermal stability of the material, and slows the decomposition reaction of polyurethane at specific temperatures (+30 °C). In contrast, the incorporation of MgO results in a slight decrease in the dielectric strength (−15%) and a significant decrease in the mechanical strength (−37%).