Providing safe drinking water to people in developing countries is an urgent worldwide water problem and a main issue in the UN Sustainable Development Goals. One of the most efficient and cheapest methods to attain these goals is to promote the use of slow sand filters. This review shows that slow sand filters can efficiently provide safe drinking water to people living in rural communities not served by a central water supply. Probably, the most important aspect of SSF for developing and less-developed countries is its function as a biological filter. WASH problems mainly relate to the spread of viruses, bacteria, and parasites. The surface and shallow groundwater in developing countries around urban areas and settlements are often polluted by domestic wastewater containing these microbes and nutrients. Thus, SSF’s function is to treat raw water in the form of diluted wastewater where high temperature and access to nutrients probably mean a high growth rate of microbes and algae but probably also high predation and high efficiency of the SSF. However, factors that may adversely affect the removal of microbiological constituents are mainly low temperature, high and intermittent flow rates, reduced sand depth, filter immaturity, and various filter amendments. Further research is thus needed in these areas, specifically for developing countries.

Activated carbons (ACs) have been the most widespread carbon materials used in supercapacitors (SCs) due to their easy processing methods, good electrical conductivity, and abundant porosity. For the manufacture of electrodes, the obtained activated carbon based on sawdust (karagash and pine) was mixed with conductive carbon and polyvinylidene fluoride as a binder, in ratios of 75% activated carbon, 10% conductive carbon black, and 15% polyvinylidene fluoride (PVDF) in an N-methyl pyrrolidinone solution, to form a slurry and applied to a titanium foil. The total mass of each electrode was limited to vary from 2.0 to 4.0 mg. After that, the electrodes fitted with the separator and electrolyte solution were symmetrically assembled into sandwich-type cell construction. The carbon’s electrochemical properties were evaluated using cyclic voltammetry (CV) and galvanostatic charge–discharge (CGD) studies in a two-electrode cell in 6M KOH. The CV and CGD measurements were realized at different scan rates (5–160 mV s⁻¹) and current densities (0.1–2.0 A g⁻¹) in the potential window of 1 V. ACs from KOH activation showed a high specific capacitance of 202 F g⁻¹ for karagash sawdust and 161 F g⁻¹ for pine sawdust at low mass loading of 1.15 mg cm⁻² and scan rate of 5 mV s⁻¹ in cyclic voltammetry test and 193 and 159 F g⁻¹ at a gravimetric current density of 0.1 A g⁻¹ in the galvanostatic charge–discharge test. The specific discharge capacitance is 177 and 131 F g⁻¹ at a current density of 2 A g⁻¹. Even at a relatively high scan rate of 160 mV s⁻¹, a decent specific capacitance of 147 F g⁻¹ and 114 F g⁻¹ was obtained, leading to high energy densities of 26.0 and 22.1 W h kg⁻¹ based on averaged electrode mass. Surface properties and the porous structure of the ACs were studied by scanning electron microscopy, energy-dispersive X-ray analysis, Raman spectroscopy, and the Brunauer–Emmett–Teller method.

The use of enterosorbents—materials which can be administered orally and eliminate toxic substances from the gastrointestinal tract (GIT) by sorption—offers an attractive complementary protection of humans against acute and chronic poisoning. In this study, we report the results of developing a microgranulated binary biomedical preparation for oral use. It was designed with a core-shell structure based on pectin with low degree of esterification as the core, and nanoporous activated carbon produced from rice husk, AC-RH, as the shell, designated as AC-RH@pectin. The adsorption properties of the synthesized materials were studied in aqueous solutions for the removal of lead (II) nitrate as a representative of toxic polyvalent metals and sodium diclofenac as an example of a medicinal drug. The composite enterosorbent demonstrated high adsorption capacity for both adsorbates studied. Adsorption kinetics of lead and diclofenac adsorption by AC-RH, pectin, and AC-RH@pectin, fitted well a pseudo-second-order model. According to the Langmuir adsorption isotherm model, the best fitted isotherm model, the maximum adsorption capacity, q_max, of AC-RH@pectin for diclofenac and for lead (II) was 130.9 mg/g and 227.8 mg/g, respectively. Although q_max of AC-RH for diclofenac, 537.6 mg/g, and q_max of pectin for lead (II), 245.7 mg/g, were higher, the maximum adsorption capacity of AC-RH for lead (II), 52.7 mg/g, was much lower than that of the composite AC-RH@pectin and the adsorption capacity of pectin for diclofenac was negligible. Therefore, the composite material AC-RH@pectin demonstrated substantial efficiency of removing both species which potentially defines it as a more universal enterosorbent suitable for treating poisoning caused by substances of different chemical nature.

Providing safe drinking water to people in developing countries is an urgent world-wide water problem and a main issue in the UN Sustainability Goals. One of the most efficient and cheapest methods to attain these goals is the use of slow sand filters. Slow sand filters can efficiently provide safe drinking water to people living in small rural communities not served by central water supply systems. The purpose of this review article is to critically summarize and synthesize features and advantages of slow sand filtration methods to improve the quality of drinking water with special focus on less-developed countries. Even though slow sand filtration is an old technique, its efficiency and cost-effectiveness make it important to continue to develop the method in parallel to other chemical and biological methods. Thus, there are needs to continue to develop methods for slow sand filtration combined with simple disinfection techniques for treatment of microbiological pollutants such as bacteria, microbes, viruses, and parasites. These techniques can be applied before or after the sand filter application. Studies are also needed to investigate other types of porous material in areas where suitable sand and gravel are not readily available. Methods are needed to reduce the contents of emerging environmental pollutants such as surfactants and microplastics. Also, further studies are needed to determine design criteria (particle size distribution, depth of media, residence time, temperature, etc.) for different types of pollutants, existing and emerging. Finally, further research is needed to advise on life cycle time, operation (e.g., batch or continuous flow), and maintenance procedures (cleaning of media, back-flushing, etc.) for used porous media in slow the sand filtration.

This work considers the quality indicators of drinking water in the Maysky district of the Pavlodar region, Republic Kazakhstan. The organoleptic, generalized, microbiological indicators, as well as organic and inorganic substances of drinking water of, water treatment plant before and after treatment, as well as tap water, were examined for compliance with regulatory requirements. The general mineralization characterizes the water as fresh and the hardness index indicates the average hardness of the water belonging to the hydrocarbonate class. An excess of the MAC norm for turbidity and manganese content before water treatment was established. The bacteriological index of water samples in the Maysky district exceeds hygienic standards. The sanitary and epidemiological hazard of water is confirmed by the presence of genus Pseudomonas aeruginosa bacteria, which indicates anthropogenic and household factors of impact, both on the natural environment and on the formation of drinking water in the Maysky district of Pavlodar region.