This article investigates a spurious resonance appearing near the antiresonance when the double-busbar configuration is applied to layered surface acoustic wave (SAW) resonators using 42 $^\circ$ YX-LiTaO $_3$ thin plates, and possible mitigation methods are studied both theoretically and experimentally. First, the origin of the spurious resonance is revealed, and the influence of structural parameters is studied using the periodic 3-D finite-element method (FEM) powered by the hierarchical cascading technique (HCT). Then, possible methods are discussed for spurious mitigation. Finally, experimental data are provided for validation of the present analysis.
16 March 2021 in Japanese Journal of Applied Physics
Piezoelectric-on-silicon MEMS resonator is very well known for its compatibility with CMOS integrated circuit technology. However, its quality factor ( Q ) is highly affected by acoustic energy loss through the supporting structures. In this study, a resonator with butterfly-like round edge resonating plate structure and deploying properly designed PnC arrays on the tether and the anchoring boundaries are proposed to scale up the quality factor by effectively reducing the energy loss. The finite element analysis simulation results reveal that the proposed topologies can efficiently change the displacement field in the resonating plate and reduce the anchor loss. Consequently, an unloaded quality factor of the conventional resonator is raised from 29 899 to 51 503 (butterfly-like round edge resonating structure), 83 349 (Phononic crystal on the tether) and 83 899 (Phononic crystal on the anchor), representing 1.7 folds, 2.78 folds and 2.8 folds improvement respectively.
10 November 2022 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
This paper discusses combination of tetragonal crystals with LiTaO 3 (LT) thin plate for complete transverse resonance suppression of surface acoustic wave devices without k 2 deterioration by manipulating the slowness shape. Besides, better lateral energy confinement is achieved as well by the use of double busbar structure. First, the mechanism of slowness shape manipulation by combining tetragonal crystals is studied. By comparison, YZ-lithium tetraborate (LBO) shows better performance than 69°Y90°X quartz. Then numerical simulations are carried out using periodic three-dimensional finite method assisted by hierarchical cascading technique, and the effectiveness of transverse mode suppression by flattening the slowness shape is revealed. And the possibility to realize temperature compensation is discussed owing to the unique material property of LBO. Moreover, the capability of other tetragonal crystals for slowness manipulation are compared, and LBO is the best choice among these tetragonal crystals.
10 March 2022 in Japanese Journal of Applied Physics
This paper discusses the applicability of dielectric materials with high acoustic impedance Za for use in A 1 Lamb mode solidly mounted resonator (SMR) with large electromechanical coupling coefficient k2 . The study first shows that the use of metal as a reflector creates parasitic capacitance Cp , which reduces k2 significantly. Then, A 1 Lamb mode SMRs are designed using HfN, HfO 2 , WN, WO 3 etc., and achievable performances are compared. When either HfN, HfO 2 , WN, or WO 3 is employed, relative large k2 up to 25% is achievable. For further k2 enhancement, a hybrid reflector configuration is also examined, wherein HfN is applied only to the top high Za layer and W is applied to the others. The result indicates that Cp caused by the W layers is still significant, and k2 becomes worse in total.
Thin-film piezoelectric-on-silicon (TPoS) microelectromechanical (MEMS) resonators are required to have high Q-factor to offer satisfactory results in their application areas, such as oscillator, filter, and sensors. This paper proposed a phononic crystal (PnC)-reflector composite structure to improve the Q factor of TPoS resonators. A one-dimensional phononic crystal is designed and deployed on the tether aiming to suppress the acoustic leakage loss as the acoustic wave with frequency in the range of the PnC is not able to propagate through it, and a reflector is fixed on the anchoring boundaries to reflect the acoustic wave that lefts from the effect of the PnC. Several 10 MHz TPoS resonators are fabricated and tested from which the Q-factor of the proposed 10 MHz TPoS resonator which has PnC-reflector composite structure on the tether and anchoring boundaries achieved offers a loaded Q-factor of 4682 which is about a threefold improvement compared to that of the conventional resonator which is about 1570.
Thin-film surface acoustic wave (TF-SAW) devices are important for wireless communication systems in the new age. Nevertheless, there are still some technical challenges including transverse mode suppression. To find out a practical solution for the challenge, this work theoretically and experimentally investigates transverse mode generation in TF-SAW devices based on LiTaO3/sapphire in which only mature and commercial materials are adopted. The devices with various Al thicknesses and wavelengths are simulated, and slowness curves, admittance curve and displacement distributions are all analyzed. A large range of wavelength from $1.6~\mu $ m to $4~\mu $ m or even larger is found for the devices to have flat slowness curves. TF-SAW resonators based on LiTaO3/sapphire without any designs for transverse mode suppression are fabricated. The transverse modes in the resonators with wavelength from $1.6~\mu $ m to $3.8~\mu $ m are all dramatically suppressed, agreeing well with the theoretical results. We believe that the suppression is sufficient, even though the transverse modes still exist. This work proposes a method to obtain TF-SAW devices with suppressed transverse mode generation, showing the strengths of LiTaO3/sapphire structure and promoting the development of TF-SAW technology.