The present review offers a detailed analysis of Photoelectrochemical (PEC) devices from metal oxide electrodes forming a semiconductor–liquid junction to protected and catalyst-decorated third generation solar cells adapted into photoelectrodes.

The optimization of multiple interfaces in hematite (α-Fe₂O₃) based composites for photoelectrochemical water splitting to facilitate charge transport in the bulk is of paramount importance to obtain enhanced solar-to-fuel efficiency. Herein, we report the fabrication of ITO/Fe₂O₃/Fe₂TiO₅/FeNiOOH multi-layer nanowires and a series of systematic experiments designed to elucidate the mechanism underlying the interfacial coupling effect of the quaternary hematite composite. The hierarchical ITO/Fe₂O₃/Fe₂TiO₅/FeNiOOH nanowires display photocurrents that are more than an order of magnitude greater than those of pristine Fe₂O₃ nanowires (from 0.205 mA cm⁻² to 2.2 mA cm⁻² at 1.23 V vs. RHE and 1 Sun), and higher than those of most of the recently reported state-of-the-art hematite composites. Structural, compositional and electrochemical investigations disclose that the surface states (SS) are finely regulated via the atomic addition of an Fe₂TiO₅ layer and FeNiOOH nanodots, while the upgrading of back contact conductivity and charge donor densities originate from the epitaxial relationship and enhanced Sn doping contributed from the ITO underlayer. We attribute the superior water oxidation performance to the interfacial coupling effect of the ITO underlayer (Sn doping and back contact conductivity promoter), the atomic level Fe₂TiO₅ coating (Ti doping, surface state density and energy level modulation) and the FeNiOOH nanodot electrocatalyst (regulating surface state energy level). Our work suggests an effective pathway for rational designing of highly active and cost-effective integrated photoanodes for photoelectrochemical water splitting.

The nanostructured BiVO4 photoanodes were prepared by electrospinning and were further characterized by XRD, SEM, and XPS, confirming the bulk and surface modification of the electrodes attained by W addition. The role of surface states (SS) during water oxidation for the as-prepared photoanodes was investigated by using electrochemical, photoelectrochemical, and impedance spectroscopy measurements. An optimum 2% doping is observed in voltammetric measurements with the highest photocurrent density at 1.23 VRHE under back side illumination. It has been found that a high PEC performance requires an optimum ratio of density of surface states (NSS) with respect to the charge donor density (Nd), to give both good conductivity and enough surface reactive sites. The optimum doping (2%) shows the highest Nd and SS concentration, which leads to the high film conductivity and reactive sites. The reason for SS acting as reaction sites (i-SS) is suggested to be the reversible redox process of V5+/V4+ in semiconductor bulk to form water oxidation intermediates by electron trapping process. Otherwise, the irreversible surface reductive reaction of VO2+ to VO2+ by electron trapping process raises the surface recombination. W doping does have an effect on the surface properties of BiVO4 electrode. It can tune the electron trapping process to obtain high concentration of i-SS and less surface recombination. This work gives a further understanding for the enhancement of PEC performance caused by W doping in the field of charge transfer at the semiconductor/electrolyte interface.

Slightly hydrogenated white TiO ₂ nanoparticles show enhanced photocatalytic performance due to their increased surface defects, while gray or black H-TiO ₂ nanoparticles display much worse catalytic performances due to the formation of bulk defects.

The responses of individual ZnO nanowires to UV light demonstrate that the persistent photoconductivity (PPC) state is directly related to the electron-hole separation near the surface. Our results demonstrate that the electrical transport in these nanomaterials is influenced by the surface in two different ways. On the one hand, the effective mobility and the density of free carriers are determined by recombination mechanisms assisted by the oxidizing molecules in air. This phenomenon can also be blocked by surface passivation. On the other hand, the surface built-in potential separates the photogenerated electron-hole pairs and accumulates holes at the surface. After illumination, the charge separation makes the electron-hole recombination difficult and originates PPC. This effect is quickly reverted after increasing either the probing current (self-heating by Joule dissipation) or the oxygen content in air (favouring the surface recombination mechanisms). The model for PPC in individual nanowires presented here illustrates the intrinsic potential of metal oxide nanowires to develop optoelectronic devices or optochemical sensors with better and new performances.