Valeria Marrocco

Dr. Valeria Marrocco

Institute of Intelligent Industrial Technologies and Systems for Advanced Manufacturing, Milan, Lombardy, Italy
orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2007 in Microelectronic Engineering
Verified
Journal Article
Closed access
TST. Stomeo
T. Stomeo
Marco GrandeMarco Grande
Marco Grande
AQAntonio Qualtieri
Antonio Qualtieri
APA. Passaseo
A. Passaseo
ASA. Salhi
A. Salhi
FPF. Prudenzano
F. Prudenzano

29 April 2020 in IEEE Access
Verified
Journal Article
Open access
Vito BasileVito Basile
Vito Basile
Marco GrandeMarco Grande
Marco Grande
Valeria MarroccoValeria Marrocco
Valeria Marrocco
DLDario Laneve
Dario Laneve
SPSavino Petrignani
Savino Petrignani
IFIrene Fassi
Irene Fassi
In this work, the inverted micro-Stereolithography (SLA) is used to show the potential of such additive manufacturing (AM) technology at prototyping super-shaped dielectric resonator antennas (S-DRAs) rapidly and accurately. The S-DRAs, which exhibit 3D complex geometries, were designed to operate at 3.5 GHz, suitable for the assessment of 5G communications in the mid band. Initially, a cross-starred-shaped S-DRA was designed and manufactured via the inverted micro-SLA by means of a photopolymer resin as material. As no information about the used material was available from literature and supplier, the dielectric properties of the photopolymer resin were characterized. Moreover, in the view of challenging further the SLA capability, several prototypes, based on the cross star shaped geometry but exhibiting a twist of variable angles along the longitudinal axis, were fabricated and tested. In order to compare the antennas performance in relation to the material volume and sizes, rectangular and cylindrical DRAs were also realized using same material and technology. Scattering parameter S11, gain, bandwidth (BW), efficiency and co- and cross-polarization of all antennas were measured. The experimental results showed that twisted S-DRAs exhibit same performance of the basic cross-starred-shaped antenna, due to the invariance to symmetry of the basic Gielis geometry. The measured gain is about 2.5 dB over a range of 1 GHz in the frequency range of interest; the BW measured for all S-DRAs is about 10%, whereas the efficiency is about 80% at 3.5 GHz. Finally, better performance in terms of bandwidth is shown by the S-DRAs, considering their dramatic volume reduction (~85%) compared to classic rectangular and cylindrical DRAs and other DRA examples already reported in the state of the art.

13 October 2011 in Optics Express
Verified
Journal Article
Closed access
PDF file
Marco GrandeMarco Grande
Marco Grande
Maria Antonietta VincentiMaria Antonietta Vincenti
Maria Antonietta Vincenti
TSTiziana Stomeo
Tiziana Stomeo
GMGiuseppe Morea
Giuseppe Morea
Roberto MaraniRoberto Marani
Roberto Marani
MSMichael Scalora
Michael Scalora
In this paper we discuss the possibility of implementing a novel bio-sensing platform based on the observation of the shift of the leaky surface plasmon mode that occurs at the edge of the plasmonic band gap of metal gratings, when an analyte is deposited on top of the metallic structure. We report numerical calculations, fabrication and experimental measurements to prove the sensing capability of a two-dimensional array of gold nano-patches in the detection of a small quantity of Isopropyl Alcohol (IPA) deposited on top of sensor surface. The calculated sensitivity of our device approaches a value of 1000 nm/RIU with a corresponding Figure of Merit (FOM) of 222 RIU−1. The presence of IPA can also be visually estimated by observing a color variation in the diffracted field. We show that color brightness and intensity variations can be ascribed to a change in the aperture size, keeping the periodicity constant, and to different types of analyte deposited on the sample, respectively. Moreover, we demonstrate that unavoidable fabrication imperfections revealed by the presence of rounded corners and surface roughness do not significantly affect device performance.

1 December 2011 in Sensors and Actuators B: Chemical
Verified
Journal Article
Closed access
Marco GrandeMarco Grande
Marco Grande
Roberto MaraniRoberto Marani
Roberto Marani
FPF. Portincasa
F. Portincasa
GMG. Morea
G. Morea
VPVincenzo Petruzzelli
Vincenzo Petruzzelli
Maria Antonietta VincentiMaria Antonietta Vincenti
Maria Antonietta Vincenti

13 October 2020 in Micromachines
Verified
Journal Article
Open access
PDF file
Valeria MarroccoValeria Marrocco
Valeria Marrocco
FMFrancesco G Modica
Francesco G Modica
Vincenzo BellantoneVincenzo Bellantone
Vincenzo Bellantone
VMValentina Medri
Valentina Medri
IFIrene Fassi
Irene Fassi
In this paper, the effect of the micro-electro discharge machining (EDM) milling machinability of Si3N4–TiN workpieces was investigated. The material removal rate (MRR) and tool wear rate (TWR) were analyzed in relation to discharge pulse types in order to evaluate how the different pulse shapes impact on such micro-EDM performance indicators. Voltage and current pulse waveforms were acquired during micro-EDM trials, scheduled according to a Design of Experiment (DOE); then, a pulse discrimination algorithm was used to post-process the data off-line and discriminate the pulse types as short, arc, delayed, or normal. The analysis showed that, for the considered process parameter combinations, MRR was sensitive only to normal pulses, while the other pulse types had no remarkable effect on it. On the contrary, TWR was affected by normal pulses, but the occurrence of arcs and delayed pulses induced unexpected improvements in tool wear. Those results suggest that micro-EDM manufacturing of Si3N4–TiN workpiece is relevantly different from the micro-EDM process performed on metal workpieces such as steel. Additionally, the inspection of the Si3N4–TiN micro-EDM surface, performed by SEM and EDS analyses, showed the presence of re-solidified droplets and micro-cracks, which modified the chemical composition and the consequent surface quality of the machined micro-features.

1 July 2019 in Journal of Manufacturing Processes
Verified
Journal Article
Closed access
Valeria MarroccoValeria Marrocco
Valeria Marrocco
FMFrancesco G Modica
Francesco G Modica
IFI. Fassi
I. Fassi