The increasing demand for sustainable materials in automotive applications, coupled with the critical need to address marine plastic pollution, presents an opportunity for innovative material development. This study explores composites made from recycled polyamide 6 (PA6) fishing nets reinforced with switchgrass fibers (0–30 wt%). The composite with 30 wt% switchgrass fibers increased tensile strength by 23% and Young’s modulus by 126% compared to unreinforced recycled PA6, achieving 93% of the tensile strength of commercial automotive-grade neat PA6 and surpassing another grade by 22%. However, higher fiber loading hindered processability, as evidenced by incomplete mold filling and reflected by a decrease in melt flow rate from 19.35 to 8.63 g/10 min. Thermal analysis revealed reduced crystallinity and crystallization temperatures with fiber addition, attributed to restricted polymer chain mobility. While dynamic mechanical analysis demonstrated improved stiffness below the glass transition temperature, scanning electron microscopy indicated optimal fiber-matrix adhesion at up to 20 wt% fiber loading, with aggregation at higher concentrations. These findings establish recycled fishing net-derived PA6/switchgrass fiber composites as a viable alternative to virgin materials in automotive applications, with mechanical properties comparable to commercial grades. Although the composites demonstrate enhanced mechanical strength and modulus, the significant reduction in ductility restricts their use to rigid, semi-structural components where flexibility is not critical. Future research should address processing challenges to enhance fiber dispersion and interfacial adhesion at higher loadings.
This study investigates the potential for recycling fishing rope waste from the Magdalen Islands, Canada, into sustainable wall cladding panels, addressing both environmental concerns and waste management challenges. A comprehensive characterization of the fishing ropes was conducted using various analytical techniques to assess their suitability for recycling. Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) identified polyethylene (PE) and isotactic polypropylene (iPP) as the main polymers present in the ropes, with a composition of approximately 25% PE and 75% PP. The effects of photodegradation were evaluated through carbonyl index analysis, differential scanning calorimetry (DSC), tensile testing, and gel permeation chromatography (GPC). The results showed reduced crystallinity, a 20% decrease in tensile strength, and lower molecular weights due to environmental exposure in comparison with unused ropes. However, melt flow rate (MFR) measurements aligned with virgin HDPE and PP values used in rope manufacturing, indicating suitable processability for recycling. Panels produced from recycled fishing ropes exhibited lower flexural and impact properties compared to commercial alternatives due to the presence of mineral contaminants and voids in the panels as revealed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). This comprehensive investigation provides valuable insights into the potential repurposing of fishing rope waste, contributing to the development of sustainable waste management strategies for coastal communities.
Eco-friendly wall cladding panels were developed from fishing industry waste by incorporating discarded ropes, wood fibers from lobster cages, and clamshell powder. Four panel formulations were investigated using MAPP and MAPE coupling agents: FRW-M (97% fishing rope), 30WF-M (67% rope with 30% wood fibers), 30CS-M (67% rope with 30% clamshell powder), and a hybrid 15CS15WF-M (67% rope with 15% each of wood fibers and clamshell powder). A DSC analysis revealed that clamshell powder addition reduced melting temperatures and crystallinity, while wood fiber incorporation led to slight increases in melting temperatures. The hybrid formulation exhibited enhanced crystallization temperatures despite lower overall crystallinity. A dynamic mechanical analysis showed an 85% improvement in storage modulus for the hybrid panel, with flexural testing demonstrating a 202% increase in modulus and 20% increase in strength. SEM-EDS analysis confirmed improved filler dispersion and interfacial adhesion in the hybrid formulation. Water absorption was lowest in FRW-M and highest in 30WF-M, while burning rate tests showed 30CS-M and 30WF-M as the best and worst performers, respectively. The hybrid formulation emerged as the optimal solution, combining enhanced mechanical properties with improved water resistance and fire retardancy, presenting a viable sustainable alternative for wall cladding applications.
The increasing demand for sustainable materials in automotive applications, coupled with the critical need to address marine plastic pollution, presents an opportunity for innovative material development. This study explores composites made from recycled polyamide 6 (PA6) fishing nets reinforced with switchgrass fibers (0–30 wt%). The composite with 30 wt% switchgrass fibers increased tensile strength by 23% and Young’s modulus by 126% compared to unreinforced recycled PA6, achieving 93% of the tensile strength of commercial automotive-grade neat PA6 and surpassing another grade by 22%. However, higher fiber loading hindered processability, as evidenced by incomplete mold filling and reflected by a decrease in melt flow rate from 19.35 to 8.63 g/10 min. Thermal analysis revealed reduced crystallinity and crystallization temperatures with fiber addition, attributed to restricted polymer chain mobility. While dynamic mechanical analysis demonstrated improved stiffness below the glass transition temperature, scanning electron microscopy indicated optimal fiber-matrix adhesion at up to 20 wt% fiber loading, with aggregation at higher concentrations. These findings establish recycled fishing net-derived PA6/switchgrass fiber composites as a viable alternative to virgin materials in automotive applications, with mechanical properties comparable to commercial grades. Although the composites demonstrate enhanced mechanical strength and modulus, the significant reduction in ductility restricts their use to rigid, semi-structural components where flexibility is not critical. Future research should address processing challenges to enhance fiber dispersion and interfacial adhesion at higher loadings.