Ahmad Zikri

Mr. Ahmad Zikri

Mechanical Engineering, Universitas Sumatera Utara, Medan, Sumatera Utara, Indonesia
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2020 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
EKEngkos Achmad Kosasih
Engkos Achmad Kosasih
Ahmad ZikriAhmad Zikri
Ahmad Zikri
MDMuhammad Irfan Dzaky
Muhammad Irfan Dzaky

12 September 2024 in RSC Advances
Verified
Journal Article
Open access
PDF file
DRDieter Rahmadiawan
Dieter Rahmadiawan
HAHairul Abral
Hairul Abral
MAMuhammad Adlan Azka
Muhammad Adlan Azka
SSS. M. Sapuan
S. M. Sapuan
RARatna Isnanita Admi
Ratna Isnanita Admi
MMMelbi Mahardika
Melbi Mahardika
Non-pressurized hot water vapor treatment significantly enhances the properties of TEMPO-oxidized bacterial cellulose films. The treatment leads to increased crystallinity, reduced porosity, and improved mechanical properties.

21 June 2022 in Heliyon
Verified
Journal Article
Open access
EKEngkos Achmad Kosasih
Engkos Achmad Kosasih
Ahmad ZikriAhmad Zikri
Ahmad Zikri
MDMuhammad Irfan Dzaky
Muhammad Irfan Dzaky
The drying method requires an effort to store food for a longer time. Some drying processes experience technical and economic weaknesses, mainly related to low efficiency, high energy costs, and decreased product quality. Various drying models have been studied to determine the suitability of heat and mass transfer analysis at drying rates in an air dehumidification scheme using different materials, one of which is silica gel. In this case, the researchers examined the effects of humidity, temperature, and airflow rate on the constant drying rate and activation energy of water desorption in silica gel using a packed bed dryer that was modified with a refrigeration system. This modified system aims to reduce specific energy consumption (SEC). The results demonstrate that the constant rate of water desorption in silica gel and the increase in air humidity cause a decrease in the constant value of the water desorption rate in silica gel. However, increases in the temperature and airflow cause an increase in the value of the constant drying rate for water desorption in silica gel, as they cause capillary evaporation. Meanwhile, the activation energy of water desorption in silica gel increases with decreasing air flow rate and increasing inlet air humidity. The attractive force acting on the water molecules from the surface force field on the surrounding walls becomes stronger if the air flow rate decreases or the air humidity increases. From the results and analysis, it is shown that the activation energy of water desorption in silica gel with significant air humidity and low flow rate, of 0.013 kg/kg d.a. (450 lpm), is the highest at 35.16 kJ/mol, whereas in silica gel with air humidity of 0.007 kg/kg d.a. (750 lpm), it is the lowest at 22.92 kJ/mol. Meanwhile, the dryer air flow rate, higher heater temperature, and lower air humidity improve the performance of the bed dryer against its evaporation rate and decrease the Specific Energy Consumption (SEC) value. SEC is also greatly influenced by the use condenser 1, which provides heater power savings of up to 79.1%. Thus, the system is expected to be applied to commercial drying systems that can work at low drying temperatures to maintain drying products and obtain low energy consumption.

14 October 2020 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
Verified
Journal Article
Open access
PDF file
Ahmad ZikriAhmad Zikri
Ahmad Zikri
EKEngkos Achmad Kosasih
Engkos Achmad Kosasih
MDMuhammad Irfan Dzaky
Muhammad Irfan Dzaky
FFFirdaus Firdaus
Firdaus Firdaus
Drying is the process of transferring heat and mass to remove water by heat application, from solid or liquid food, to decrease water content. The temperature and drying conditions imposed on a product have an essential influence on it. Drying in high temperatures can cause damage the sensitive materials. To overcome this problem, in this paper, to show the effect of temperature, specific humidity and mass flow rate, on the specific energy consumption on the use of air heaters, and the combination refrigeration system to produce hot and dry air. In this study, we use an experimental method by using temperature variations of 60°C, 90°C, 120°C, and 150°C. Air mass flow rates using 100 Lpm, 150 Lpm, 200 Lpm, and 250 Lpm variation. The air from the environment is sucked up by the blower and then enters the evaporator. In the evaporator, the air will condensate so the air will get the low relative humidity. The heat in the condenser is used as preheating the dry air before entering the heater. To produce hot and dry air with the minimum humidity ratio (3.9 g / kg dry air) for the same target temperature is recommended to use a 100Lpm airflow rate by adjusting the evaporator pressure to 2.6 bar. Then, to obtain the minimum SECR (0.928), the recommended target temperature is 120°C, by adjusting the airflow rate to 250Lpm and the pressure at the evaporator 1.6 bar.

28 March 2023 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
EKEngkos Achmad Kosasih
Engkos Achmad Kosasih
MDMuhammad Irfan Dzaky
Muhammad Irfan Dzaky
Ahmad ZikriAhmad Zikri
Ahmad Zikri
ARAlmacho Rachmanudiputra
Almacho Rachmanudiputra
FAFaizal Abizar
Faizal Abizar
YSYarynara Sebrio Suharyadi
Yarynara Sebrio Suharyadi

19 June 2023 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
Verified
Journal Article
Open access
PDF file
MDMuhammad Irfan Dzaky
Muhammad Irfan Dzaky
EKEngkos Achmad Kosasih
Engkos Achmad Kosasih
IHImansyah Ibnu Hakim
Imansyah Ibnu Hakim
Ahmad ZikriAhmad Zikri
Ahmad Zikri
The drying process is the key to the quality of the coffee produced. The allowable moisture content of coffee beans is 12%. The air mass flux, specific humidity, and the drying temperature are varied using a bed dryer drying system combined with a double condenser refrigeration system. Robusta coffee beans are used in this research to obtain the characterization of coffee beans. The highest drying rate constant is obtained by 2.44 × 10-4 s-1 directly proportional to the increased air mass flux and drying air temperature, with a value of 1.701 kg/s m2 and 80 °C, but inversely proportional to the specific humidity, with a value of 7.01 g/kg d.a. The lowest activation energy value was 31.88 kJ/mol when the air mass flux was 1.701 kg/s m2, the drying air temperature was 80 °C, and the average specific humidity was 7.01 g/kg d.a. In this work, the developed correlation is proposed to practically predict the activation energy (EA) and the pre-exponential factor (A) with equation and respectively. Based on Ea and A correlation equation, it can be used for designing a bed dryer type coffee drying system for a larger scale.