Amina Mukhamedova

Ms. Amina Mukhamedova

D. Serikbayev East Kazakhstan State Technical University, Ust-Kamenogorsk, Kazakhstan
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
BRBauyrzhan Rakhadilov
Bauyrzhan Rakhadilov
Аlexander D. PogrebnjakАlexander D. Pogrebnjak
Аlexander D. Pogrebnjak
ZSZhuldyz Sagdoldina
Zhuldyz Sagdoldina
Dastan BuitkenovDastan Buitkenov
Dastan Buitkenov
BVBeresnev Vyacheslav
Beresnev Vyacheslav
AMAmina Mukhamedova
Amina Mukhamedova
This work is devoted to the study of the formation of nanostructured multilayer coatings (TiZr/Nb)N on the surface of an AISI 321 steel substrate depending on the deposition parameters of the Arc-PVD method. The results of the X-ray diffraction analysis showed the formation of solid solution (TiNb)N and ZrN in the multilayer coatings with an FCC structure, ε-NbN with a hexagonal structure, as well as with a small volume fraction of the ε-Ti2N and β-Nb2N phase. On the basis of phase composition data, it is possible to assume that an increase in the number of bilayers leads to a decrease in the nitrogen concentration in the bilayers and, consequently, to a decrease in the volume fraction of ε-NbN and β-Nb2N nitrides. In all investigated systems obtained at −100 V and −200 V bias potentials, ε-NbN is the main phase. The study of the element distribution over the thickness of the (TiZr/Nb)N coating confirms the results of the X-ray diffraction analysis. The use of the structure model in the form of alternating layers allows for significantly improving the adhesion characteristics of the protective coating, as well as ensuring their high hardness. Based on the experimental results, it is possible to analyze changes in the mechanical and tribological properties of multilayer coatings depending on the number of applied bilayers. The results of the study of the elastic modulus and hardness of multilayer coatings (TiZrNb)N with different numbers of bilayers showed that a large number of bilayers (small thickness of each individual layer) shows the lowest value of hardness. It is assumed that as the bilayer thickness decreases, the coating characteristics are closer to the monolayer alloy than to the multilayer structure.

Verified
Journal Article
Open access
PDF file
RGRiza Gabdyssalyk
Riza Gabdyssalyk
Kuat KombayevKuat Kombayev
Kuat Kombayev
KSKaribek Tagaevich Sherov
Karibek Tagaevich Sherov
DZDaulet Zhamsap
Daulet Zhamsap
AMAmina Mukhamedova
Amina Mukhamedova
This study systematically evaluates the microstructural characteristics, cross-sectional microhardness profiles, and dry sliding friction dynamics of Stoodite 6-M, AISI 1065-type (Np-65G, GOST 10543-98), and AISI 307-type stainless steel (Sv-08Cr20Ni9Mn7Ti, GOST 2246-70) coatings deposited on 09G2S low-alloy steel via gas tungsten arc welding (GTAW). Microstructural evolution and elemental distributions were characterized using optical microscopy and SEM/EDS, while functional properties were assessed via cross-sectional Vickers microhardness profiling (HV0.05) and rotary ball-on-disk friction testing. All surfacing systems produced sound, defect-free fusion interfaces, developing cobalt-matrix dendritic, acicular/packet-lath, and fine cellular-dendritic austenitic structures for Stoodite 6-M, AISI 1065, and AISI 307, respectively. The core cladding microhardness peaked in AISI 307 (505 ± 18 to 525 ± 20 HV0.05), which may be associated with its alloy composition and observed microstructural features, followed by Stoodite 6-M (445 ± 15 to 468 ± 12 HV0.05) and AISI 1065 (355 ± 14 to 438 ± 16 HV0.05). Tribological signal analysis revealed a distinct divergence between static mechanical strength and kinetic sliding behavior: AISI 1065 demonstrated the lowest mean steady-state friction coefficient following initial running-in (μmean = 0.532, SD = 0.019–0.023, CV = 3.57–4.28%), whereas Stoodite 6-M exhibited a higher steady-state friction coefficient (μmean = 0.613, SD = 0.022–0.026, CV = 3.60–4.20%) alongside superior running-in stability, and AISI 307 recorded an intermediate value (μmean = 0.566, SD = 0.035–0.041, CV = 6.19–7.17%). These findings demonstrate that microhardness, mean friction force, and signal stability operate as uncoupled material selection parameters. The study defines baseline friction performance under dry contact conditions, emphasizing the necessity of evaluating contact kinetics independently from bulk mechanical hardness.

1 January 2024 in Recent Contributions to Physics
Verified
Journal Article
Open access
PDF file
AMAmina Mukhamedova
Amina Mukhamedova
APAlexander Dmitrievich Pogrebnjak
Alexander Dmitrievich Pogrebnjak
ГУГ.к. Уазырханова
Г.к. Уазырханова
БРБ.қ. Рахадилов
Б.қ. Рахадилов
In this work, the adhesive and tribological characteristics of (TiZrNbYAl)N multilayer coatings were studied. The main goal of this work is to assess the influence of the number of layers on the adhesive and tribological characteristics of the (TiZrNbYAl)N coating deposited on 12Х18Н9Т steel substrates. A study of the distribution of elements over the depth of coatings using Auger electron spectroscopy showed that chemical elements are distributed quite evenly over the cross section of the coatings and the element distribution curves have sharp peaks. The presence of iron in the coating composition at a depth of more than 2 microns on the coating side indicates that an increase in electrical displacement ensures reliable adhesion of the coating to the steel substrate, which is confirmed by the results of testing the coatings for adhesive strength. An increase in the application time of each individual layer at Upp=-100 V and P= 4×10-3 Torr leads to an uneven distribution of elements throughout the thickness of the coatings and the formation of a relatively wide transition coating-substrate layer. Tests of the adhesive strength of coatings have shown that all coatings wear out when scratched, but do not peel off, i.e., they are destroyed by a cohesive mechanism associated with plastic deformation and the formation of fatigue cracks in the coating material. Different coating modes correspond to different values of acoustic emission depending on the load. It was determined that the coatings obtained at Upp =-100 V; P = 4×10-3 Torr showed high adhesive strength and some degree of delamination in the scratch area at the maximum test load. The results of tribological studies showed that (TiZrNbYAl)N coatings have a high friction coefficient, the average value of which is μ=0.85-0.95. Such values can be explained by the high roughness of wear tracks due to cohesive destruction of coatings.

3 December 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
Аlexander D. PogrebnjakАlexander D. Pogrebnjak
Аlexander D. Pogrebnjak
ABAlexander Borisov
Alexander Borisov
ZTZhanar Tekebayeva
Zhanar Tekebayeva
BMBauyrzhan Maratuly
Bauyrzhan Maratuly
AJAlexey Jes
Alexey Jes
AMAmina Mukhamedova
Amina Mukhamedova
This article investigated Ta-Cu and Nb-Cu coatings deposited via magnetron sputtering from metal targets with varying copper content. Scanning electron microscopy (SEM) combined with energy dispersive spectroscopy (EDS) revealed that the coatings had an average thickness of 2.5 μm, with a Cu composition of approximately 10 wt.% and Ta exceeding 86%, with the remaining percentages attributed to carbon and oxygen from the residual vacuum chamber atmosphere. It was observed that increasing the coating thickness from 2.5 μm to 8.5 μm did not result in a significant change in nanohardness (3.29 GPa) in Nb-Cu coatings, although the elastic modulus increased by 15% (from 81 to 95 GPa). Ta-Cu coatings demonstrated superior antibacterial properties compared to Nb-Cu coatings. Consequently, Ta-Cu coatings exhibit considerable potential for further applications due to their favorable structural properties and enhanced antibacterial efficacy.