The building sector is known to have a significant environmental impact, considering that it is the largest contributor to global greenhouse gas emissions of around 36% and is also responsible for about 40% of global energy consumption. Of this, about 50% takes place during the building operational phase, while around 10–20% is consumed in materials manufacturing, transport and building construction, maintenance, and demolition. Increasing the necessity of reducing the environmental impact of buildings has led to enhancing not only the thermal performances of building materials, but also the environmental sustainability of their production chains and waste prevention. As a consequence, novel thermo-insulating building materials or products have been developed by using both locally produced natural and waste/recycled materials that are able to provide good thermal performances while also having a lower environmental impact. In this context, the aim of this work is to provide a detailed analysis for the thermal characterization of recycled materials for building insulation. To this end, the thermal behavior of different materials representing industrial residual or wastes collected or recycled using Sardinian zero-km locally available raw materials was investigated, namely: (1) plasters with recycled materials; (2) plasters with natural fibers; and (3) building insulation materials with natural fibers. Results indicate that the investigated materials were able to improve not only the energy performances but also the environmental comfort in both new and in existing buildings. In particular, plasters and mortars with recycled materials and with natural fibers showed, respectively, values of thermal conductivity (at 20 °C) lower than 0.475 and 0.272 W/(m⋅K), while that of building materials with natural fibers was always lower than 0.162 W/(m⋅K) with lower values for compounds with recycled materials (0.107 W/(m⋅K)). Further developments are underway to analyze the mechanical properties of these materials.

Our research aims to achieve dual-positive effects in the presented study by raising photovoltaic (PV) panels over the water surface. With this, target experiments were primarily conducted to evaluate the efficiency increments of the PV panel while reducing its operating temperature through passive convective cooling obtained by raising it over water. The following objective was to estimate the reduction in water evaporation due to the shading effect induced by the panel placed inside the same basin. The performance of two PV panels was analyzed, one used for tests, the other as a reference. The characteristic curves were determined under the local environmental conditions of Cagliari, Italy. The true temperature reduction and efficiency gain calculations of panel P1 due to water cooling was achieved via the measured temperatures and calculated efficiencies of panel P2 at environmental conditions. The water height inside the basin was constantly monitored and maintained at approximately 7.5 cm below panel P1, which covered about 17% of the total water surface area. The presence of water underneath P1 leads to its efficiency increment on average by 2.7% (absolute) and about 17.22% (relative). At the same time, temperature of panel P1 dropped by 2.7 °C on average. The comparative water evaporation study conducted with and without P1 inside the basin showed a 30% reduction in water evaporation.

Sustainable building materials for integrated (structural and thermal) retrofitting are the need of the hour to retrofit/upgrade the seismic vulnerable and ill-insulated existing building stocks. At the same time, the use of natural fibers and their recyclability could help construct safer and more sustainable buildings. This paper presents three aspects of jute fiber products: (1) the evaluation of the mechanical performance of the jute nets (2.5 cm × 2.5 cm and 2.5 cm and 1.25 cm mesh configurations) through tensile strength tests (with the aim for these to be used in upgrading masonry wall with natural fiber textile reinforced mortars (NFTRM) systems); (2) the hundred percentage recyclability of left-over jute fibers (collected during the net fabrication and failed nets post-tensile strength tests) for the composite mortar preparation; (3) and the evaluation of insulation capacity of the recycled jute net fiber composite mortar (RJNFCM) through thermal conductivity (TC) measurements, when a maximum amount of 12.5% of recycled jute fiber could be added in the mortar mixture at laboratory conditions and with available instruments Notably, when more than the said amount was used, the fiber–mortar bonding was found to be not optimal for the composite mortar preparation. These studies have been carried out considering these products’ applicability for integrated retrofitting purposes. It has been found that the denser mesh configuration (2.5 cm × 1.25 cm) is 35.80% stiffer than the other net configurations (2.5 cm × 2.5 cm). Also, the mesh configuration (2.5 cm × 1.25 cm) shows about 60% more capability to absorb strain energy. TC tests have demonstrated the moderate insulation capacity of these composite mortar samples, and the TC values obtained from the tests range from 0.110 (W/mK) to 0.121 (W/mK).