The suppression of unnecessary radio-electronic noise and the protection of electronic devices from electromagnetic interference by the use of pliable highly microwave radiation absorbing composite materials based on polymers or rubbers filled with conductive and magnetic fillers have been proposed. Since the working frequency bands of electronic devices and systems are rapidly expanding up to the millimeter wave range, the capabilities of absorbing and shielding composites should be evaluated for increasing operating frequency. The point is that the absorption capacity of conductive and magnetic fillers essentially decreases as the frequency increases. Therefore, this paper is devoted to the absorbing capabilities of composites filled with high-loss dielectric fillers, in which absorption significantly increases as frequency rises, and it is possible to achieve the maximum frequency selective of absorption due to electromagnetic and electromechanical resonances.
In this work, we present a procedure for manufacturing a soft capacitive strain sensor in the form of a multi-layer electrical capacitor for further integration into the elastic gear rim of a jaw coupling. The dielectric elastomer sensor (DES) is based on an elastomeric substrate with alternating layers of conductive carbon black based ink as electrode layers and elastomeric film as a dielectric and electrical insulation. A variety of thin multi-layer sensors were produced to evaluate the manufacturing process. Additionally, using an LCR meter and a tensile test machine, the equivalent electrical capacitance (C) at the two sensor contacts and the applied force are measured, respectively. It is shown that C varies depending on the amount of sample strain caused by the applied force. By testing two versions of DES, a maximum change in capacitance of ΔC = 1.55 pF was achieved. The obtained characteristics show that the presented manufacturing process for the DES can be used as a soft strain sensor to measure the strain caused by the force applied to the elastic element between the jaw couplings.
In recent years, industry and research (i) have driven the development and application of data-driven machines and systems and (ii) have increasingly introduced predictive maintenance. One of the main challenges is the acquisition of representative data for these applications. In the scope of mechanical systems, machine elements are the key parts for measuring process relevant data. Thereby, elastic couplings offer a considerable potential for a wide range of applications. The present work describes a novel space neutral sensor-integrating gear rim of a jaw coupling for the measurement of torque, rotational speed and temperature. The mechanical modifications on the coupling and the applied dielectric elastomer sensor are outlined. Additionally, the electrical conceptualization and the measurement chains are described. A manufactured prototype of the sensor-integrating jaw coupling and a proof of concept are presented.
This work investigates the hyper-viscoelastic behavior of a thermoplastic polyurethane IROGRAN A 92 E 5670 FCM used in the gear rim of a jaw coupling. The aim is to provide the material parameters for the modeling of jaw couplings in engineering tasks. Uniaxial compression tests were conducted at various temperatures and loading speeds to fit a hyper-viscoelastic material model. The material model uses the Yeoh free energy and the power law model with one Maxwell element. The parametrized material model showed very good results in comparison to experimental data. In addition, the influence of friction on the experiments was modeled, investigated, and discussed. Further component tests for a jaw coupling of size 28 were conducted with two different specimen types. The original gear rim and a modified gear rim with central boreholes for integrated sensors were used in the test. The influence of such a modification was investigated with four different loading cases, focusing on the torsion-torque characteristic and the relative damping. These component tests enable the validation of numerical models of jaw couplings.
The possibility to directly measure the torque transmitted from a motor to a machine is not an easy task. To alleviate this, in the current work a new prototype of a sensor-integrating jaw coupling is proposed. In the prototype, double-sided counterbores are drilled into the teeth of the gear rim. Afterwards, dielectric elastomer sensors (DESs) are inserted, which are connected to strain amplifiers at both ends. The change in the capacitance of the sensors can then later be used to predict the torque. In the present work, the new prototype of the sensor-integrating jaw coupling is experimentally and numerically evaluated. Additionally, the manufactured DESs were subjected to multiple compressive loading-unloading cycles using a tensile testing machine to characterize them. It was shown for the first time that the coupling is able to detect the application of a torsion angle independent of the loading direction, i.e. clockwise or counterclockwise. Additionally, the correlation between the applied load and the measured change in capacitance is very good. Furthermore, a framework for the numerical simulation of both conventional and sensor-integrating jaw coupling is given and validated with experimental data. The model was implemented in the finite element software ABAQUS. To account for the viscous material properties of the material of the gear rim a hyper-viscoelastic material model was used. For the prediction of the torque, the numerical model yielded excellent results when compared to the experimental data.
1 August 2024 in Proceedings in Applied Mathematics and Mechanics
Shaft misalignments are one of the main causes of damage to couplings in machines. If they are not detected in time, they can lead to machine downtimes. When assembling a machine, however, it is not always possible to align the shafts perfectly. Elastic couplings are able to compensate for such misalignments up to a certain degree. To detect the present radial misalignment, the concept of a sensor‐integrating jaw coupling, developed to determine the transmitted torque, is used. In the teeth of the gear rim, boreholes are drilled and dielectric elastomer sensors (DES) are inserted. If the teeth deform during use of the coupling the DES will deform as well, leading to a change in capacitance, which can be detected. If the two shafts, which the coupling connects, are perfectly aligned to each other, each of the loaded teeth will deform uniformly. However, if there is a radial or angular misalignment, the deformation is different for each tooth, which can be determined with the help of the DES. To demonstrate this effect, a finite element model of the sensor‐integrating jaw coupling with misalignments is created, and numerical simulations are conducted. In this model, the hyper‐viscoelastic material behavior of (i) the gear rim of the jaw coupling and (ii) the DES is taken into account. From the mechanical simulation, the deformed state of the DES is obtained, which is used to compute the capacitance of the sensor. With the results of the numerical simulations, a symbolic regression is performed. The result is an analytical formula that makes the accurate detection of the present radial misalignment possible. The developed framework can later be easily programmed on a microcontroller which is integrated in the sensor‐integrating jaw coupling.