Packaging constitutes the largest end-use market for plastics, accounting for approximately 40% of total consumption by sector. In 2021, the average plastic packaging waste generated per European Union (EU) resident was 35.9 kg, of which 14.2 kg, or around 40%, was recycled. The Directive on Packaging and Packaging Waste (94/62/EC), a pivotal environmental regulation, mandates specific recycling targets: a minimum of 50% of all plastic packaging waste must be recycled by 2025, increasing to at least 55% by 2030. These targets underscore the necessity for further advancements in the plastic and composite packaging waste sector. This review uses a PESTEL analysis to provide a comprehensive overview of six critical factors influencing the recycling of plastic and composite packaging waste. The PESTEL framework encompasses political, economic, socio-cultural (social), technological, environmental, and legal dimensions. This review underscores the key aspects of each factor that influences recycling. Moreover, the discussion outlines the key deficiencies within the recycling system for plastic and composite packaging waste, including factors such as inadequate technological capacity, the underdevelopment of the secondary polymer market, and the establishment of ambitious political targets that are challenging to attain, among others. The questions raised underscore areas that warrant further investigation.
The composition of plastic and multilayer packaging waste was assessed in the mixed municipal solid waste (MSW) streams of the Kaunas (Lithuania), Daugavpils (Latvia) and Tallinn (Estonia) municipalities. For the analysis of samples in the mixed MSW streams, the authors used manual sorting and a visual recognition method. Composition analysis of plastic and multilayer packaging waste from separately collected waste of multi-family and single-family households was performed in the Kaunas and Tallinn municipalities. For the analysis of samples in the separately collected waste streams, the research group combined manual sorting and near-infrared (NIR) spectroscopy methods. The findings reveal that the percentage distribution of plastic and multilayer packaging waste within the municipal solid waste (MSW) stream is relatively consistent across the municipalities of Kaunas, Daugavpils and Tallinn, comprising 40.16%, 36.83% and 35.09%, respectively. However, a notable variation emerges when examining separately collected plastic and multilayer packaging waste streams. In this category, the proportion of plastic and multilayer packaging within the total separately collected packaging waste stream ranges from 62.05% to 74.7% for multi-family residential buildings and from 44.66% to 56.89% for single-family residential buildings. The authors provided further insights for the enhanced recycling potential of different plastic materials through improved sorting.
The slow pyrolysis of macroalgae at moderate temperatures in the reactor used resulted in an oil with a slightly better calorific value than that of the literature, but the other properties were not convincing. Therefore, co-pyrolysis with HDPE offers a way out in this study. However, this did not improve the property profile as a fuel, as the co-pyrolysate was incombustible due to its high water content. Only a mixture of the pyrolysis oil from algae and of the HDPE wax from the initial pyrolysis of HDPE resulted in a diesel-like product: the density was from 807 kg m−3, the viscosity 3.39 mm2 s−1, the calorific value was 46 MJ kg−1, and the oxidation stability was 68 min. The isoparaffin index indicates only a low branching of the paraffins, and therefore a low research octane number of 80. The blend did not need any further stabilizing additives.
In 2020, 29.5 million tonnes of post-consumer plastics waste were collected in the EU. Around 40% of all plastic waste consists of packaging waste, and therefore it is one of the most important components of plastic waste. According to the Eurostat data, the amount of plastic packaging waste generated in the Lithuania, Latvia, and Estonia in 2020 was around 86, 46.7 and 53.6 thousand tonnes or 30.8, 24.6 and 40.3 kilograms per capita respectively. In 2020, the waste management of post-consumer plastic packaging in the EU had the following trends – 46% was sent to recycling, 37% to energy recovery and 17% to landfill. The EU has set itself the goal of recycling of plastic packaging waste at the EU level by at least 50% by 2025 and 55% by 2030. In this case particular attention is paid to the packaging waste management. The results of waste morphological investigations carried out in three municipalities (Kaunas, Daugavpils, and Tallinn) in 2023 showed that the plastic content of separately collected plastic waste is up to 67%, while the plastic content of mixed municipal waste is up to 40%. LD-PE, HD-PE and PP are the predominant plastic wastes. The recycling rate of plastic packaging waste in all Baltic countries is likely to be up to 45%, which leaves it out of line with the EU's recycling targets for plastic packaging. For improving the management and the recycling of plastic packaging waste, the following observations of investigation were drawn: Plastics packaging waste recycling rates are higher when collected separately compared to mixed waste collection schemes (may varied around 13-80 times). Due to the different physicochemical properties of plastic polymers, waste from different plastics should be collected separately to increase the potential recycling rate. Implementation of new recycling methods for plastic waste to improve the recycling of pure and contaminated plastic waste. Improvement of the waste sorting line in waste treatment facilities towards higher separation efficiency for plastics of different polymers. Further research is needed to improve the plastic waste management scheme and implement technical solutions. Editorial note (2026): This abstract was prepared for reference purposes using artificial intelligence technology, based on the original publication, without the involvement of the author(s).
About Me
Chemical Engineering and Sustainable Management and Production scientific area.
Chemical Engineering and Sustainable Management and Production scientific area.