Electron transport layers (ETLs) play a fundamental role in perovskite solar cells (PSCs) through charge extraction. Here, we developed flexible PSCs on 12 different kinds of ETLs based on SnO2. We show that ETLs need to be specifically developed for plastic substrates in order to attain 15% efficient flexible cells. Recipes developed for glass substrates do not typically transfer directly. Among all the ETLs, ZnO/SnO2 double layers delivered the highest average power conversion efficiency of 14.6% (best cell 14.8%), 39% higher than that of flexible cells of the same batch based on SnO2-only ETLs. However, the cells with a single ETL made of SnO2 nanoparticles were found to be more stable as well as more efficient and reproducible than SnO2 formed from a liquid precursor (SnO2-LP). We aimed at increasing the understanding of what makes a good ETL on polyethylene terephthalate (PET) substrates. More so than ensuring electron transport (as seen from on-current and series resistance analysis), delivering high shunt resistances (RSH) and lower recombination currents (Ioff) is key to obtain high efficiency. In fact, RSH of PSCs fabricated on glass was twice as large, and Ioff was 76% lower in relative terms, on average, than those on PET, indicating considerably better blocking behavior of ETLs on glass, which to a large extent explains the differences in average PCE (+29% in relative terms for glass vs PET) between these two types of devices. Importantly, we also found a clear trend for all ETLs and for different substrates between the wetting behavior of each surface and the final performance of the device, with efficiencies increasing with lower contact angles (ranging between ∼50 and 80°). Better wetting, with average contact angles being lower by 25% on glass versus PET, was conducive to delivering higher-quality layers and interfaces. This cognizance can help further optimize flexible devices and close the efficiency gap that still exists with their glass counterparts.
31 March 2022 in ACS Sustainable Chemistry & Engineering
The technology of organometal halide perovskites is on the verge of the lab to fab transition due to particularly high efficiencies and low cost of the raw materials employed in the active later. The hole transport layer is a key enabling component of such solar cells and at the same time the one requiring more significant synthetic efforts. Alternative materials with improved sustainability are under constant development, yet 2,2′,7,7′-tetrakis(N,N-di(4-methoxyphenyl)amino)-9,9′-spirobifluorene (Spiro-OMeTAD) still represents the standard in the field. We show that the combination of solventless approaches, chemistry on water, and micellar catalysis gives access to such critical material in a fully sustainable, scalable, and efficient way. Performances are validated in devices delivering results equal to those with standard commercial Spiro-OMeTAD but greatly reducing the overall E-factor─a green chemistry metric measuring the waste/purified product ratio of a synthesis, from 5299 to 555, as well as eliminating chlorinated solvents and hazardous chemicals.
Indoor photovoltaics harvests energy from light available inside homes and buildings for powering the Internet of Things, wireless sensors and consumer and medical electronics. A major challenge in this field is a lack of standardized testing conditions. Here a team from more than 60 research institutions and companies proposes best practices for evaluating indoor photovoltaic performance and establishing baseline stability tests. We base these recommendations on recent experimental data, published literature, practices used in academic and industrial settings, technical specifications from standards organizations, lighting databases and existing regulations. We outline procedures that begin with the recommendation of a single artificial light source, followed by guidance on setting up measurement systems and a step-by-step guide for conducting measurements and tests. These procedures are consolidated into three checklists. Our aim is to promote accurate measurement of laboratory and commercial solar cells and modules under indoor lighting, facilitating comparability across academia and industry worldwide.
We present a big leap in performance for indoor photovoltaics by developing flexible perovskite solar cells (PSCs) on ultra-thin flexible glass (FG). We manufactured roll-to-roll ITO-coated FG with excellent transmittance (> 80%) and sheet resistance (13 Ω/square ) and impressive bendability. Rather than resulting in planar structures which worked best for thick rigid glass-based cells, optimized PSCs on the ultrathin FG incorporate instead a mesoporous scaffold over thin SnO2 compact layers that significantly contributed to the achievement of breakthrough power conversion efficiencies (PCEs) of 20.6% (16.7 m W cm-2 power density), and 22.6% (35.0 m W cm-2) under 200 and 400 lx LED illumination respectively. These represent the highest reported for any existing flexible photovoltaic technology tested in indoors, surpassing by a huge 60-90% margin the prior best-performing flexible PSCs, as a result of significantly lower recombination currents and series resistances, higher fill factors and shunt resistances. Ultra-thin glass flexible PSCs can become the key enabling technology for the indoor electronics of the future, being lightweight, conformable and highly efficient.