Dominik Bortis

Dominik Bortis

Auto-generated profile, based on publicly available information

Dominik Bortis

Power Electronic Systems Laboratory, ETH Zurich, Zurich, Switzerland

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 December 2018 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
DRDaniel Rothmund
Daniel Rothmund
TGThomas Guillod
Thomas Guillod
DBDominik Bortis
Dominik Bortis
JKJohann Kolar
Johann Kolar
The power supply chain of data centers from the medium voltage (MV) utility grid down to the chip level voltage consists of many series connected power conversion stages and accordingly shows a relatively low efficiency. Solid-State Transformers (SSTs) could improve the efficiency by substantially reducing the number of power conversion stages and/or directly interfacing the MV AC grid to a 400V DC bus, from where server racks with a power consumption of several tens of kilowatts could be supplied by individual SSTs. The recent development of SiC MOSFETs with a blocking voltage of 10 kV enables the realization of a simple and hence highly reliable two-stage SST topology, consisting of an AC/DC PFC rectifier and a subsequent isolated DC/DC converter. In this context, an isolated 25kW, 48 kHz, 7 kV to 400V series resonant DC/DC converter based on 10 kV SiC MOSFETs is realized and tested in this paper. To achieve zero voltage switching (ZVS) of all MOSFETs, a special modulation scheme to actively control the amount of the switched magnetizing current on the MV and LV side is implemented. Furthermore, the design of all main components and especially the electrical insulation of the employed medium frequency (MF) transformer is discussed in detail. Calorimetric efficiency measurements show that a full-load efficiency of 99.0% is achieved, while the power density reaches 3.8kW=L (63W=in3).

10 December 2018 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
DRDaniel Rothmund
Daniel Rothmund
TGThomas Guillod
Thomas Guillod
DBDominik Bortis
Dominik Bortis
JKJohann Kolar
Johann Kolar
Due to their extremely high energy demand, data centers are directly supplied from a medium voltage (MV) grid. However, a significant part of this energy is dissipated in the power supply chain, since the MV is reduced step-by-step through multiple power conversion stages down to the chip voltage level. In order to increase the efficiency of the power supply chain, the number of conversion stages must be substantially reduced. In this context, Solid-State Transformers (SSTs) are considered as a possible solution as they could directly interface the MV AC grid to a 400V DC bus, whereby server racks with a power consumption of several tens of kilowatts could be directly supplied from an individual SST. With a focus on the lowest system complexity, the SST ideally should be built as simple two-stage system consisting of an MV AC/DC PFC rectifier stage followed by an isolated DC/DC converter. Accordingly, this paper focuses on the design and realization of a 25kW, 3.8kV single-phase AC to 7kV DC PFC rectifier unit based on 10kV SiC MOSFETs. By simply adding an LC-circuit between the switch nodes of the well-known full-bridge-based PWM AC/DC rectifier, the integrated Triangular Current Mode (iTCM) concept is implemented, which only internally superimposes a large triangular current ripple on the AC mains current and therefore enables zero voltage switching (ZVS) over the entire AC mains period. Special attention is paid to the realization of the MV inductors and their electrical insulation, the AC-input LCL-filter to limit EMI emissions, and the challenges arising due to cable resonances when connecting the SST to the MV grid via a MV cable. Despite the large insulation distances required for MV, the realized 25kW MV PFC rectifier achieves an unprecedented power density of 3.28kW=L (54W=in3) and a full-load efficiency of 99.1%, determined using a calorimetric measurement setup, which is discussed in detail in the Appendix.

20 July 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
DRDaniel Rothmund
Daniel Rothmund
DBDominik Bortis
Dominik Bortis
JKJohann Kolar
Johann Kolar
The characterization of soft-switching losses of modern high-voltage SiC MOSFETs is a difficult but necessary task in order to provide a sound basis for the accurate modelling of converter systems, such as medium-voltage-connected Solid- State Transformers (SSTs), where soft-switching techniques are employed to achieve an improved converter efficiency. Switching losses, in general, are typically measured with the well-known double pulse method. In case of soft-switching loss measurements, however, this method is very sensitive to the limited accuracy of the measurement of the current and voltage transients, and thus is unsuitable for the characterization of fast switching high-voltage MOSFETs. This paper presents an accurate and reliable calorimetric method for the determination of soft-switching losses using the example of 10 kV SiC MOSFET modules. Measured soft-switching loss curves are presented for different DC-link voltages and switched currents. Furthermore, a deeper analysis concerning the origin of soft-switching losses is performed. With the proposed measurement method, it can be experimentally proven that the largest share of the soft-switching losses arises from charging and discharging the output capacitance of the MOSFET module and especially of the antiparallel junction barrier Schottky diode.

6 December 2018 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
MGMattia Guacci
Mattia Guacci
MHMorris Heller
Morris Heller
DNDominik Neumayr
Dominik Neumayr
DBDominik Bortis
Dominik Bortis
JKJohann Kolar
Johann Kolar
OHOliver Haberlen
Oliver Haberlen
The unprecedented performance potential of Gallium- Nitride-on-Silicon (GaN-on-Si) High Electron Mobility Transistors (HEMTs) is seen as the key enabler for the design of power converters featuring extreme power-density figures, as demanded in next generation power electronics applications. However, unexpected loss mechanisms, i.e. dynamic Rds,on phenomena and Cosslosses, are appearing in currently available GaN transistors and are compromising their operation. In this paper, measurements of Coss-losses are performed in a dedicated calorimetric measurement setup and, through a systematic approach, the root cause of the loss mechanism is potentially identified. Afterwards, with the essential support of a manufacturer of power semiconductors, a novel transistor, featuring an enhanced multi-layer III-N buffer, is developed according to the acquired knowledge. A significant reduction in terms of Coss-losses, i.e. of soft-switching losses, and the absence of dynamic Rds,on phenomena are verified experimentally on the new device. These achievements enable a significant performance improvement for future soft-switching power converters featuring GaN-on-Si HEMTs.

27 September 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
MGMattia Guacci
Mattia Guacci
JAJon Azurza
Jon Azurza
KPKessy L. Pally
Kessy L. Pally
DBDominik Bortis
Dominik Bortis
JKJohann Kolar
Johann Kolar
GDGerald Deboy
Gerald Deboy
The increasing demand for higher power densities and higher efficiencies in power electronics, driven by the aerospace, electric vehicle and renewable energy industries, encourages the development of new converter concepts. In particular, modular and/or multi-level (M/ML) topologies are employed to break the performance barriers of state-of-the-art power converters by simultaneously reducing the system losses and volume/weight. These improvements mainly originate from the replacement of high voltage transistors, typical of two-level converters, with low voltage, e.g. 200V, devices, offering superior electric performance. Hence, two low on-state resistance silicon (Si) and gallium nitride (GaN) 200V power semiconductors are comprehensively characterized in this paper to support the multi-objective optimization and the design of M/ML power converters. First, the selected devices are analyzed experimentally determining their conduction, thermal and switching characteristics; for this purpose, a novel ultra-fast transient calorimetric measurement method is introduced and explained in detail. In the course of this analysis, an unexpected switching loss mechanism is observed in the Si devices at hand; the physical reason of this behavior is clarified and it is proven to be solved in next generation research samples, which are also characterized by measurements. Finally, the influence of the measured power semiconductors performance on the overall efficiency and power density of a typical converter is determined through a case study analyzing a hard switching half-bridge operated as single-phase inverter, i.e. the fundamental building block of several M/ML topologies. It is concluded that, in this voltage and power class, GaN e-FETs are nowadays approximately a factor of three superior to Si Power MOSFETs; however, the better heat dissipation achieved by the latter still makes them the preferred solution for higher power applications.

14 April 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
DNDominik Neumayr
Dominik Neumayr
GKGustavo Carlos Knabben
Gustavo Carlos Knabben
EVElise Varescon
Elise Varescon
DBDominik Bortis
Dominik Bortis
JKJohann Kolar
Johann Kolar
One of the key technical challenges of the Google & IEEE Little Box competition, an international contest to build the world’s smallest 2kW single-phase inverter in 2015, was to shrink the volume of the energy storage required to cope with the twice mains-frequency (120 Hz) pulsating power at the AC side and meet the stringent 2:5% input voltage ripple at the DC side. In this paper, first, a full-power processing bucktype converter active buffer approach, selected by the 1st prize winner of the Little Box Challenge (LBC) is analyzed in detail. Being relieved from strict voltage ripple requirements, a larger voltage ripple is allowed across the buffer capacitor significantly reducing the capacitance requirement. Second, a partial-power active buffer approach, selected by the 2nd prize winner of the LBC, where conventional passive capacitive buffering of the DClink is combined with a series-connected auxiliary converter, used to compensate the remaining 120 Hz voltage ripple across the DClink capacitance, is studied in detail. In this paper, both selected concepts are comparatively evaluated in terms of achievable efficiency, power density and ripple compensation performance under both stationary and transient conditions. Novel control schemes and optimally designed hardware prototypes for both considered buffer concepts are presented and accompanied with experimental measurements to support the claimed efficiency and power density and assess the performance of the implemented control systems. Finally, by means of comparison with conventional passive DC-link buffering using only electrolytic capacitors, it is determined at what voltage ripple requirement it actually becomes beneficial in terms of volume to employ the considered active buffer concepts.