Venkata Chaitanya Krishna Chekuri

Venkata Chaitanya Krishna Chekuri

Auto-generated profile, based on publicly available information

Venkata Chaitanya Krishna Chekuri

School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA, USA

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 August 2020 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Closed access
JKJinwoo Kim
Jinwoo Kim
GMGauthaman Murali
Gauthaman Murali
HPHeechun Park
Heechun Park
EQEric Qin
Eric Qin
HKHyoukjun Kwon
Hyoukjun Kwon
SLSung Kyu Lim
Sung Kyu Lim
A new trend in system-on-chip (SoC) design is chiplet-based IP reuse using 2.5-D integration. Complete electronic systems can be created through the integration of chiplets on an interposer, rather than through a monolithic flow. This approach expands access to a large catalog of off-the-shelf intellectual properties (IPs), allows reuse of them, and enables heterogeneous integration of blocks in different technologies. In this article, we present a highly integrated design flow that encompasses architecture, circuit, and package to build and simulate heterogeneous 2.5-D designs. Our target design is 64-core architecture based on Reduced Instruction Set Computer (RISC)-V processor. We first chipletize each IP by adding logical protocol translators and physical interface modules. We convert a given register transfer level (RTL) for 64-core processor into chiplets, which are enhanced with our centralized network-on-chip. Next, we use our tool to obtain physical layouts, which is subsequently used to synthesize chip-to-chip I/O drivers and these chiplets are placed/routed on a silicon interposer. Our package models are used to calculate power, performance, and area (PPA) and reliability of 2.5-D design. Our design space exploration (DSE) study shows that 2.5-D integration incurs 1.29x power and 2.19x area overheads compared with 2-D counterpart. Moreover, we perform DSE studies for power delivery scheme and interposer technology to investigate the tradeoffs in 2.5-D integrated chip (IC) designs.

2 June 2019
Verified
Conference Paper
Open access
JKJinwoo Kim
Jinwoo Kim
GMGauthaman Murali
Gauthaman Murali
HPHeechun Park
Heechun Park
EQEric Qin
Eric Qin
HKHyoukjun Kwon
Hyoukjun Kwon
SLSung Kyu Lim
Sung Kyu Lim
A new trend in complex SoC design is chiplet-based IP reuse using 2.5D integration. In this paper we present a highly-integrated design flow that encompasses architecture, circuit, and package to build and simulate heterogeneous 2.5D designs. We chipletize each IP by adding logical protocol translators and physical interface modules. These chiplets are placed/routed on a silicon interposer next. Our package models are then used to calculate PPA and signal/power integrity of the overall system. Our design space exploration study using our tool flow shows that 2.5D integration incurs 2.1x PPA overhead compared with 2D SoC counterpart.

28 October 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
ASArvind Singh
Arvind Singh
MKMonodeep Kar
Monodeep Kar
VCVenkata Chaitanya Krishna Chekuri
Venkata Chaitanya Krishna Chekuri
SMSanu K. Mathew
Sanu K. Mathew
ARAnand Rajan
Anand Rajan
SMSaibal Mukhopadhyay
Saibal Mukhopadhyay
This article demonstrates enhanced power (P) and electromagnetic (EM) side-channel analysis (SCA) attack resistance of standard (unprotected) 128-bit advanced encryption standard (AES) engines with parallel (P-AES, 128-bit) and serial (S-AES, 8-bit) datapaths and a 128-bit SIMON engine with the bit-serial (1-bit) datapath by an on-die security-aware all-digital low-dropout (DLDO) regulator. The proposed DLDO improves SCA resistance using control-loop-induced perturbations in a nominal DLDO, enhanced by a random switching noise injector (SNI) by power-stage control and a randomized reference voltage (R-VREF) generator coupled with all-digital clock modulation (ADCM). SCA performed on the measured power/EM signatures acquired from a 130-nm CMOS testchip demonstrates up to 25x reduction in test vector leakage assessment (TVLA) leakage for P-AES and 3579x, 2182x, and 500x increase in minimum-traces-to-disclose (MTD) 80% of the subkeys for P-AES, S-AES, and SIMON cores, respectively, with respect to correlation power analysis (CPA) and correlation EM analysis (CEMA).

17 September 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
JKJinwoo Kim
Jinwoo Kim
VCVenkata Chaitanya Krishna Chekuri
Venkata Chaitanya Krishna Chekuri
NRNael Mizanur Rahman
Nael Mizanur Rahman
MDMajid Ahadi Dolatsara
Majid Ahadi Dolatsara
HTHakki Mert Torun
Hakki Mert Torun
SLSung Kyu Lim
Sung Kyu Lim
In this article, we present an effective methodology for co-design, co-analysis, and the system-level optimization of chiplet/interposer power delivery network (PDN) in 2.5-D integrated chip (IC) designs. In our methodology, we first generate a commercial-grade heterogeneous 2.5-D IC designs including full signal routing and power delivery. We then perform our PDN co-analysis in frequency and time domains on the entire PDN to evaluate various mechanisms added to our PDN designs. Based on our co-analysis results, we perform the system-level optimization on both interposer and chiplet PDNs with the stable performance of power delivery. Finally, we perform power, performance, and area (PPA) analysis and power integrity (PI) on our 2.5-D designs and discuss tradeoffs in chiplet and interposer levels due to PDN optimization. Our experiments show 27.17% improvement in the overall IR-drop in the optimized 2.5-D IC design by increasing the interposer PDN occupancy by 5.52% and inserting the additional PDN grids in chiplet designs. However, we also observe tradeoffs in terms of PPA and PI. By PDN optimization, the optimized design has an 11.6% increase of the total power, while the area of 2.5-D design remains the same. Moreover, from the perspective of PI, the tradeoffs are shown by 0.6% reduction of power efficiency, 32.6% higher output ripple, and 31.5% higher initial ringing because of an inductive behavior of interposer PDN in the optimized design.

1 November 2019
Verified
Conference Paper
Closed access
HTHakki Mert Torun
Hakki Mert Torun
HYHuan Yu
Huan Yu
NDNihar Dasari
Nihar Dasari
VCVenkata Chaitanya Krishna Chekuri
Venkata Chaitanya Krishna Chekuri
ASArvind Singh
Arvind Singh
MSMadhavan Swaminathan
Madhavan Swaminathan
Integrated voltage regulators (IVR) with embedded inductors is an emerging technology that provides point-of-load voltage regulation to high-performance systems. Conventional two-step approaches to the design of IVRs can suffer from suboptimal design as the optimal inductor depends on the characteristics of the buck converter (BC). Furthermore, inductor-level trade-offs such as AC and DC resistance, inductance and area can not be determined independently from the BC. This co-dependency of the BC and the inductor creates a highly non-linear response surface, which raises the necessity of co-optimization, involving multiple time-consuming electromagnetics (EM) simulations. In this paper, we propose a machine learning based optimization methodology that eliminates EM simulations from the optimization loop to significantly reduce the optimization complexity. A novel technique named as Spectral Transposed Convolutional Neural Network (S-TCNN) is presented to derive an accurate predictive model of the inductor frequency response using a small amount of training data. The derived S-TCNN is then used along with a time-domain model of the BC to perform multi-objective optimization that approximates the Pareto front for 5 objectives, namely inductor area, BC settling time, voltage conversion efficiency, droop and ripple. The resulting methodology provides multiple Pareto optimal inductors in an efficient and fully automated fashion, thereby allows to rapidly determine the optimal trade-offs for possibly contradicting design objectives. We demonstrate the proposed framework on co-optimization of solenoidal inductor with magnetic core and BC that are integrated on silicon interposer.

22 October 2020 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
HPHeechun Park
Heechun Park
JKJinwoo Kim
Jinwoo Kim
VCVenkata Chaitanya Krishna Chekuri
Venkata Chaitanya Krishna Chekuri
MDMajid Ahadi Dolatsara
Majid Ahadi Dolatsara
MNMohammed Nabeel
Mohammed Nabeel
SLSung Kyu Lim
Sung Kyu Lim
Interposer-based 2.5D integrated circuits (ICs) enable the chip-level reuse of hard intellectual properties (IPs), also known as chiplets. Such system-level integration shortens the design cycle considerably for large-scale and heterogeneous chips. Besides traditional interposers, which only provide passive elements and routing, active interposers are furthermore comprised of logic components. When implemented carefully using a dedicated electronic design automation (EDA) flow, an active interposer can significantly improve the design quality and flexibility for 2.5D ICs. In this paper, we present a complete EDA flow and design strategies targeting such active interposerbased 2.5D ICs. Our key contributions include the co-analysis of power, performance, signal and power integrity, and the related co-optimization of chiplets and the active interposer. Our benchmark is a 64-core RISC-V architecture, organized into multiple chiplets and interconnected by a system-level networkon- chip (NoC). For efficiency, we embed the NoC routers and integrated voltage regulators (IVRs) into the active interposer. Moreover, we integrate security monitors into the interposerbased NoC to protect the system and its shared memories against adversarial traffic. The simple yet powerful benefit of this implementation is to offer security by construction, as it is based on a clear physical separation between critical and trusted components (the system-level NoC) versus commodity components (the chiplets). We contrast our active, secured design to a passive, unsecured design baseline of the same RISC-V benchmark, and we find that the active design reduces the silicon area by 18.5%, power by 3.2%, and IR-drop by 73.7%, respectively.