A new trend in system-on-chip (SoC) design is chiplet-based IP reuse using 2.5-D integration. Complete electronic systems can be created through the integration of chiplets on an interposer, rather than through a monolithic flow. This approach expands access to a large catalog of off-the-shelf intellectual properties (IPs), allows reuse of them, and enables heterogeneous integration of blocks in different technologies. In this article, we present a highly integrated design flow that encompasses architecture, circuit, and package to build and simulate heterogeneous 2.5-D designs. Our target design is 64-core architecture based on Reduced Instruction Set Computer (RISC)-V processor. We first chipletize each IP by adding logical protocol translators and physical interface modules. We convert a given register transfer level (RTL) for 64-core processor into chiplets, which are enhanced with our centralized network-on-chip. Next, we use our tool to obtain physical layouts, which is subsequently used to synthesize chip-to-chip I/O drivers and these chiplets are placed/routed on a silicon interposer. Our package models are used to calculate power, performance, and area (PPA) and reliability of 2.5-D design. Our design space exploration (DSE) study shows that 2.5-D integration incurs 1.29x power and 2.19x area overheads compared with 2-D counterpart. Moreover, we perform DSE studies for power delivery scheme and interposer technology to investigate the tradeoffs in 2.5-D integrated chip (IC) designs.
17 September 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
In this article, we present an effective methodology for co-design, co-analysis, and the system-level optimization of chiplet/interposer power delivery network (PDN) in 2.5-D integrated chip (IC) designs. In our methodology, we first generate a commercial-grade heterogeneous 2.5-D IC designs including full signal routing and power delivery. We then perform our PDN co-analysis in frequency and time domains on the entire PDN to evaluate various mechanisms added to our PDN designs. Based on our co-analysis results, we perform the system-level optimization on both interposer and chiplet PDNs with the stable performance of power delivery. Finally, we perform power, performance, and area (PPA) analysis and power integrity (PI) on our 2.5-D designs and discuss tradeoffs in chiplet and interposer levels due to PDN optimization. Our experiments show 27.17% improvement in the overall IR-drop in the optimized 2.5-D IC design by increasing the interposer PDN occupancy by 5.52% and inserting the additional PDN grids in chiplet designs. However, we also observe tradeoffs in terms of PPA and PI. By PDN optimization, the optimized design has an 11.6% increase of the total power, while the area of 2.5-D design remains the same. Moreover, from the perspective of PI, the tradeoffs are shown by 0.6% reduction of power efficiency, 32.6% higher output ripple, and 31.5% higher initial ringing because of an inductive behavior of interposer PDN in the optimized design.
22 October 2020 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Interposer-based 2.5D integrated circuits (ICs) enable the chip-level reuse of hard intellectual properties (IPs), also known as chiplets. Such system-level integration shortens the design cycle considerably for large-scale and heterogeneous chips. Besides traditional interposers, which only provide passive elements and routing, active interposers are furthermore comprised of logic components. When implemented carefully using a dedicated electronic design automation (EDA) flow, an active interposer can significantly improve the design quality and flexibility for 2.5D ICs. In this paper, we present a complete EDA flow and design strategies targeting such active interposerbased 2.5D ICs. Our key contributions include the co-analysis of power, performance, signal and power integrity, and the related co-optimization of chiplets and the active interposer. Our benchmark is a 64-core RISC-V architecture, organized into multiple chiplets and interconnected by a system-level networkon- chip (NoC). For efficiency, we embed the NoC routers and integrated voltage regulators (IVRs) into the active interposer. Moreover, we integrate security monitors into the interposerbased NoC to protect the system and its shared memories against adversarial traffic. The simple yet powerful benefit of this implementation is to offer security by construction, as it is based on a clear physical separation between critical and trusted components (the system-level NoC) versus commodity components (the chiplets). We contrast our active, secured design to a passive, unsecured design baseline of the same RISC-V benchmark, and we find that the active design reduces the silicon area by 18.5%, power by 3.2%, and IR-drop by 73.7%, respectively.
12 August 2020 in IEEE Transactions on Electromagnetic Compatibility
One of the favorable tools for signal integrity evaluation is eye diagram analysis. This is traditionally performed with a lengthy transient simulation, which can be prohibitively time consuming for complex high-speed channels with a low bit error rate. Methods for eye estimation exist; however, they are either only applicable to linear time-invariant systems or have lack in accuracy or efficiency. In this article, an optimization-based approach is proposed to quickly obtain the worst-case eye diagram characteristics. This approach focuses on the inter-symbol interference since its effect can span over many symbols and include crosstalk, making it challenging to model. In this article, the data patterns leading to the lowest voltage corresponding to a high symbol, the highest voltage corresponding to a low symbol, and the times of minimum and maximum level crossing points are calculated. Then, eye height, eye width, and the worst-case eye opening are estimated using these points. To reduce complexity, the proposed approach includes a mapping algorithm that exploits the Gray code. Additionally, Bayesian optimization is used because of its efficiency and good performance on non-linear and non-convex problems. Finally, the application of the proposed approach to high-speed SerDes channels, and channels in system-on-package designs is evaluated with numerical examples, where the results show its accuracy and efficiency.
28 December 2023 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
In this article, we present three commercial-grade 3-D IC designs based on state-of-the-art design technologies, specifically microbumping (3-D die stacking), hybrid bonding (wafer-on-wafer bonding), and monolithic 3-D (M3D) ICs. To highlight tradeoffs present in these three designs, we perform analyses on power, performance, and area (PPA) and the clock tree. We also model the tier-to-tier interconnection in each 3-D IC methodology and analyze signal integrity (SI) to assess the reliability of each design. From our experiments using the OpenPiton benchmark, the hybrid bonding design shows the best timing improvement of 81.4% when compared to its 2-D counterpart, while microbumping shows the best reliability among 3-D IC designs. Moreover, we expand our study to the commercial processor architecture, which is Arm Cortex-A53, with the new set of 3-D integration options. In addition, we show the microbump assignment methodology to handle a large number of 3-D interconnections in the microbumping 3-D design. We also perform SI on the new set of 3-D intertier/interdie connections to discuss the reliability based on their physical dimensions. With a new benchmark design, the hybrid-bonding 3-D shows the best energy–delay-product (EDP) improvement, which is 25.8% compared to 2-D, and the largest eye-opening among 3-D integration options.
17 January 2023 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Nanoscale interlayer vias (ILVs) in monolithic 3-D (M3D) ICs have enabled high-density vertical integration of logic and memory tiers. However, the sequential assembly of M3D tiers via wafer bonding is prone to variability in the immature fabrication process and manufacturing defects. The yield degradation due to ILV faults can be mitigated via dedicated test and diagnosis of ILVs using built-in self-test (BIST). Prior work has carried out fault localization for a regular 1-D placement of ILVs in the M3D layout where shorts are assumed to arise only between unidirectional ILVs. However, to minimize wirelength in M3D routing, ILVs may be irregularly placed by a place-and-route tool, and shorts can also occur between an up-going ILV and a down-going ILV. To test and localize faults in realistic ILV layouts, we present a new BIST framework that is optimized for test time and PPA overhead. We also present a graph-theoretic approach for representing potential fault sites in the ILVs and carry out inductive fault analysis to drop noncritical sites. We describe a procedure for optimally assigning ILVs to the BIST pins and determining the BIST configuration for test-cost minimization. Evaluation results for M3D benchmarks demonstrate the effectiveness of the proposed framework.