Gallium Nitride High Electron Mobility Transistors (GaN HEMTs) enable higher efficiency, higher power density, and smaller passive components resulting in lighter, smaller and more efficient electrical systems as opposed to conventional Silicon (Si) based devices. This paper investigates the detailed benefits of using GaN devices in transportation electrification applications. The material properties of GaN including the applications of GaN HEMTs at different switch ratings are presented. The challenges currently facing the transportation industry are introduced and possible solutions are presented. A detailed review of the use of GaN in the Electric Vehicle (EV) powertrain is discussed. The implementation of GaN devices in aircraft, ships, rail vehicles and heavy-duty vehicles is briefly covered. Future trends of GaN devices in terms of cost, voltage level, gate driver design, thermal management and packaging are investigated.
21 November 2019 in IEEE Transactions on Power Electronics
In recent years, there has been a trend for improved performance in semiconductor switches, allowing power electronic systems to achieve higher efficiency and higher power density. This desired improvement has led to the adoption of Silicon Carbide (SiC) and Gallium nitride (GaN)-based switches due to the fact that Silicon (Si) has been reaching its material limit. Wide-bandgap (WBG) devices obtain faster switching speeds. Therefore, they require higher level measurement technologies to analyze them. In this paper, the theoretical loss breakdown of a GaN-based power electronic system is presented including an analysis of its dynamic behavior. Several methods of measurement are presented to quantify the behavior of fast switching.
9 January 2017 in IEEE Transactions on Power Electronics
In single-phase ac high-voltage (HV) battery chargers, as the input current is enforced to be varying sinusoidally in phase with the input voltage, the pulsating power at two times of the line frequency will be seen on the dc-link. Bulky capacitor bank or extra active filter (AF) circuits are needed to assimilate this harmonic current, which become a major barrier in terms of power density and cost. Sinusoidal charging method can be applied, while this might affect the charging efficiency and a deep study is still needed to further investigate on the impact to the Lithium-ion battery. An active filter auxiliary power module (AFAPM) based dual-mode dual-voltage charging system for vehicle application has been proposed. The AFAPM converter has two modes: the HV active filtering mode, in which the vehicle is connected to the grid and the converter assimilates the significant second-order harmonic current; and the low-voltage (LV) battery charging mode, in which the vehicle is running and the converter charges the LV battery from HV battery. However, a relay and inductors are still required in that converter to achieve the dual-mode operation. This paper proposes a primary full-integrated AFAPM for electrified vehicle applications with single-phase onboard chargers. The proposed AFAPM converter is composed of a two-phase bidirectional buck converter to work as an AF and a dual-active-bridge to operate as a LV battery charger auxiliary power module (APM). With the proposed converter, only an extra active energy storage capacitor is needed to achieve the active filtering. All the switches and inductors on the primary stage are shared between the AF and APM. Therefore, the use of a bulky capacitor bank or an additional AF circuit is avoided and, thus, the cost, size, and weight of the dual-voltage charging system in the electrified vehicle applications can be reduced. A 720-W prototype has been built to confirm the effectiveness of the proposed converter.
17 May 2016 in IEEE Transactions on Power Electronics
In single-phase onboard chargers for electrified vehicles, second-order harmonic currents and corresponding ripple voltages exist on the dc bus. The low-frequency harmonic current is normally filtered using a bulk film capacitor or an additional active filter (AF) circuit. This presents an obstacle for improving the power density as well as reducing the cost. This paper proposes a simple and effective method that reduces the bulk capacitor in single-phase chargers and alleviates the low-frequency sinusoidal harmonic current in automotive applications. It applies the low-voltage (LV) battery charger auxiliary power module as an AF to filter the low-frequency harmonic currents in the high-voltage (HV) battery charger when the HV battery is charging. Hence, the integrated active filter auxiliary power module (AFAPM)-based dual-voltage charging system can achieve the AF function without extra power switches, heat sinks, and corresponding gate-drive circuits. In addition, the proposed AFAPM converter can obtain an almost unchanged switch rating to achieve 2.4-kW LV battery charging and 6.6-kW HV active filtering functions. Therefore, the proposed method can reduce the cost for the dual-voltage charging system in electrified vehicles. A 1.2-kW proof-of-concept prototype has also been built and experiments show promising results confirming the effectiveness of the proposed concept.
20 April 2020 in IEEE Transactions on Transportation Electrification
Gallium Nitride enhancement-mode high electron mobility transistors (GaN E-HEMTs) can achieve high frequency and high efficiency due to its excellent switching performance compared with conventional Si transistors. Nevertheless, GaN HEMTs exhibit a more pronounced dynamic on-state resistance RDS(on) than silicon transistors. The variation of RDS(on) is caused by both the static RDS(on) due to junction temperature rise and the dynamic RDS(on) due to the electron trapping. Without a careful decoupling analysis, it is difficult to calculate and model the dynamic RDS(on) portion. This paper introduces a comprehensive approach of dynamic RDS(on) evaluation, comprising four techniques: 1) a clamping circuit for both the hard-switching (HS) device and synchronous rectification (SR) device; 2) a junction temperature monitoring technique; 3) control of both the pulse test and soak time; 4) continuous operation of device under test. Based on the dynamic RDS(on) test results, a new model of the RDS(on) variation is developed where two coefficients: kTj and kdR are defined to model the contribution of the heating effect and the impact of the trapping effect, respectively. The RDS(on) model is validated by the comparison between the calculated and measured junction temperatures of a 650 V/30 A GaN-based half-bridge. Furthermore, a detailed loss breakdown analysis is conducted for the GaN-based hard-switching half-bridge. Results show that the switching losses, Eon and Eoff are the dominant loss factors with high switching frequency. At last, the possible efficiency improvements are also discussed in detail.
25 November 2020 in IEEE Transactions on Power Electronics
Similar to other power semiconductors, Gallium Nitride enhancement-mode high electron mobility transistors (GaN E-HEMTs) require short-circuit protection (SCP) or over-current protection (OCP) in practical applications. However, the fast-switching characteristic of GaN introduces the challenge to the protection. For SCP, the traditional methods are either too slow or not practical for GaN. Therefore, an alternative SCP solution which is fast and easy to implement is much desired. For high power density applications, it is also popular to integrate OCP into the gate driver. Therefore, a fast protection circuit that can be used for either SCP or OCP is desirable. In this paper, an ultrafast discrete circuit-based protection circuit is proposed for GaN HEMTs. It includes a first soft turn-off stage and a second hard turn-off stage. The soft turn-off stage effectively limits the voltage spike over the device. Following the soft turn-off stage, the hard turn-off stage will cut off the PWM signal immediately completely. A dual-gate implementation approach is further proposed for devices with two gate pads. The method has been verified by both SPICE simulation and hardware implementations for both SCP and OCP. The experimental results show that the total propagation delay time for SCP is only 125ns while the normal switching performance is not affected.