Manuel Fernandez

Manuel Fernandez

Auto-generated profile, based on publicly available information

Manuel Fernandez

BSH Home Appliances Group, Zaragoza, Spain

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 February 2017 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
MFM. Fernandez
M. Fernandez
XPXavier PERPIÑA
Xavier PERPIÑA
JRJ. Roig
J. Roig
MVMiquel Vellvehi
Miquel Vellvehi
FBF. Bauwens
F. Bauwens
MTM. Tack
M. Tack
Gallium Nitride High-Electron-Mobility Transistors (GaN HEMTs) are promising devices for high-frequency and high-power density converters, but some of their applications (e.g., motor drives) require high robustness levels. In this scenario, 600 V normally-off p-GaN gate HEMTs are studied under Short-Circuit (SC) by experiment and physics-based simulations (drift-diffusion and thermodynamic models). A strong drain current reduction (>70% after saturation peak) and high gate leakage current (tens of mA) are observed. All studied devices withstand the SC test at bus voltages up to 350 V, while fail at 400 V. Furthermore, its understanding is crucial to improving SC ruggedness in p-GaN HEMTs.

20 September 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
MFManuel Fernandez
Manuel Fernandez
XPXavier PERPIÑA
Xavier PERPIÑA
MVMiquel Vellvehi
Miquel Vellvehi
OAOriol Aviñó
Oriol Aviñó
SLSergio Llorente
Sergio Llorente
XJXavier Jordà
Xavier Jordà
A test bench is proposed to study, at die-level, the power losses and current distribution in power devices. It is based on an infrared camera and a flexible half-bridge resonant inverter with a tunable resonance frequency f res . With this setup, the die surface temperature is acquired in steady state, while the device is under real operation. The power losses are derived from the temperature mean value averaged, first, over a few switching cycles and, then, across the die surface. By contrast, the current distribution is inferred from the spectral component of the surface thermal map at the switching frequency (f Sw ). As a proof of concept, two case studies are reported considering 650 V-40 A insulated gate bipolar transistors (IGBTs) soft- and hard-switched within and outside the zero voltage switching condition. First, the power losses are analyzed under switching conditions representative of domestic induction heating applications (f res = 29.6 kHz) at f Sw = 40 kHz and f Sw = 20 kHz. Second, the power losses and local current distribution are investigated when f res = 9.25 kHz at f Sw ranged from 8.91 to 9.51 kHz. Such results are assessed with power losses electrical measurements and simulations, obtaining a satisfactory agreement. Moreover, hot spots are identified as current crowding points at f Sw , whose location is fixed by the bonding wires attachment to the die and the device edge termination. As main benefits of this technique, a higher spatial resolution is achieved and problems related with noisy electrical measurements resulting from the insertion of the used probes or transducers, power circuit stray elements, or device packaging parasitics are avoided.

21 November 2016
Verified
Conference Paper
Closed access
XJXavier Jordà
Xavier Jordà
XPXavier PERPIÑA
Xavier PERPIÑA
MVMiquel Vellvehi
Miquel Vellvehi
MFManuel Fernandez
Manuel Fernandez
SLSergio Llorente
Sergio Llorente
SASandra Aranda
Sandra Aranda
Power electronics applications require an accurate thermal management design. In this sense, one of the most important elements are thermal interface materials (TIMs) placed between the power devices and heatsinks in order to provide good thermal contact and (eventually) electrical isolation. To predict accurate thermal performances of the final assemblies, direct thermal tests are practically unavoidable, as the final thermal behaviour of TIMs depends on many parameters, such as mounting pressure, surface roughness, etc. and datasheets are often incomplete. Such thermal tests could be complex in final industrial systems and for this reason we propose a simple TIM evaluation setup for predicting the final thermal behaviour of IGBT-based inverters using such materials. The results obtained from two thermal pad TIMs and silicone grease are compared showing a good agreement with those obtained in test vehicles using functional IGBTs.

1 February 2017
Verified
Conference Paper
Closed access
MFM. Fernandez
M. Fernandez
XPX. Perpina
X. Perpina
MVMiquel Vellvehi
Miquel Vellvehi
DSD. Sanchez
D. Sanchez
XJXavier Jordà
Xavier Jordà
SLS. Llorente
S. Llorente
The numerous limitations of Electro Mechanical Relays (EMRs) for implementing Single-Pole, Single-Throw (SPST) Bi-Directional Switches (BDS) lead to new developments based on power semiconductor devices. This work gives an insight into the design and operation of BDSs based on the combination of unidirectional voltage blocking and bidirectional current conduction power devices, which aim to substitute EMRs in home appliances. The developed BDSs are fully characterized.

16 March 2026 in IEEE Transactions on Power Electronics
Verified
Journal Article
Open access
CFConrad Ferrer
Conrad Ferrer
MFManuel Fernández
Manuel Fernández
MVMiquel Vellvehi
Miquel Vellvehi
SLSergio Llorente
Sergio Llorente
XJXavier Jordà
Xavier Jordà
XPXavier PERPIÑA
Xavier PERPIÑA
Die-level electrical stress caused by current crowding is investigated in Insulated Gate Bipolar Transistors (IGBTs) outside zero-voltage switching (ZVS) operation. This stress occurs during the turn-on phase of an induction cooking resonant inverter, where the switching frequency sweeps from 150 to 50 kHz. The stress is monitored on a sub 100 μs timescale with a 10 μm lateral resolution using an infrared (IR) thermographic setup. To improve signal-to-noise ratio and time resolution, a Fourier based time reconstruction strategy is applied. Electrothermal SPICE simulations complement the interpretation of measurements, providing insights into current crowding under such stressful operating conditions. The analysis under soft-start conditions reveals two key findings. First, heat dissipation, and consequently current conduction, present a time dependent two-dimensional distribution, with hotspots forming in low-impedance regions detectable via IR thermography. Second, in this non-homogeneous current distribution, the SPICE electrothermal model predicts the most frequently occurring value of the temperature distribution (statistical mode) across the active area more accurately than the mean value. This observation may establish a link to the concept of junction temperature, which is traditionally derived using thermo-sensitive electrical parameters.