Nano- and micro-electromechanical systems (N/MEMSs) are traditionally based on electrostatic or piezoelectric coupling, which couples electrical and mechanical energy through acoustic resonator structures. Most recently, N/MEMS devices based on magnetoelectrics are gaining much attention. Unlike electrostatic or piezoelectric N/MEMS that rely on an AC electric field or voltage excitation, magnetoelecric N/MEMS rely on the electromechanical resonance of a magnetostrictive/piezoelectric bilayer heterostructure exhibiting a strong strain-mediated magnetoelectric coupling under the excitation of a magnetic field and/or electric field. As a consequence, magnetoelectric N/MEMS enable unprecedented new applications, ranging from magnetoelectric sensors, ultra-compact magnetoelectric antennas, etc. This Tutorial will first outline the fundamental principles of piezoelectric materials, resonator design, specifically different acoustic modes, and piezoelectric-based N/MEMS applications, i.e., radio frequency front end filters and infrared radiation sensors. We will then provide an overview of magnetoelectric materials and N/MEMS focusing on the governing physics of the magnetoelectric effect, magnetic material properties for achieving high magnetoelectric coupling, state-of-the-art magnetoelectric N/MEMS devices, and their respective applications.
20 January 2022 in IEEE Transactions on Electron Devices
This article demonstrates, for the first time, a zero-power ultrasonic wakeup receiver for intra-body communication with Implantable Medical Devices (IMDs). The system is based on a 10 x 10 Piezoelectric Micromachined Ultrasonic Transducer (pMUT) array, a zero-power 500 nm gap MEMS plasmonic switch, a low-leakage CMOS load-switch, and an ad hoc sensing circuit. An ultrasonic signal of 10 mVpp is received by the pMUT array at a distance of 5 cm and brings the MEMS switch from the off-state (1 pA) to the on-state (20 μ A) when biased at 9.09 $V_{DC}$ . This small current then wakes up the load-switch (<10 nW when off), which powers up the sensing circuit to decode the pMUT signal. The system is demonstrated in a tissue phantom, making it ideal for intrabody communication.
1 January 2021 in Journal of Microelectromechanical Systems
This article reports on the first demonstration of a high resolution (~1.9 nW/Hz 1/2 measured in 200 Hz bandwidth) and fast (~5.3 ms) uncooled Infrared (IR) detector based on a high frequency (172 MHz) aluminum nitride nano-plate piezoelectric fishnet-like metasurface (PFM). For the first time, an ultrathin (650 nm) piezoelectric fishnet-like metasurface is employed to form the vibrating body of a nanoelectromechanical resonator with a unique combination of optical, thermal and electromechanical properties. Sensing and actuation of a high frequency and high electromechanical performance (quality factor, Q ~2254 and electromechanical coupling coefficient, k t2 ~1.4%) bulk acoustic mode of vibration in the free-standing ultrathin structure is achieved thanks to the superior piezoelectric transduction properties of the proposed metasurface. Strong absorption (60%) of mid wavelength infrared (MWIR) radiation in the ultra-low volume resonant device is obtained thanks to the properly engineered optical properties of the fishnet-like metasurface which provide multiple plasmonic resonances at 3-5 μm to the structure. The demonstrated resonant PFM detector technology marks a milestone towards the implementation of a new class of high performance, miniaturized and low power MWIR imaging systems.
4 May 2004 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Interconnect test for highly integrated environments becomes more important in terms of its test time and a complete diagnosis, as the complexity of the circuit increases. Since the board-level interconnect test is based on boundary scan technology, it takes a long test time to apply test vectors serially through a long scan chain. Complete diagnosis is another important issue. Since the board-level test is performed for repair, noticing the faulty position is an essential element of any interconnect test. Generally, the interconnect test algorithms that need a short test time cannot perform the complete diagnosis and the algorithms that perform the complete diagnosis need a lengthy test time. To overcome this problem, a new interconnect test algorithm is developed. The new algorithm can provide the complete diagnosis of all faults with a shorter test time compared to the previous algorithms.
9 February 2022 in Journal of Microelectromechanical Systems
This paper presents an in-depth thermomechanical analysis of zero-power micromechanical photoswitches (MPs) aiming at aggressive performance enhancement for applications that require ultralow infrared (IR) detection threshold. An accurate analytical model was first derived and used to maximize the thermal sensitivity of the MPs through a loop-based optimization program. With specific pre-defined boundary conditions, such a program can be used to generate a set of device geometrical parameters leading to highest possible thermal sensitivity without sacrificing the structural strength of the device (i.e., spring constant), which otherwise will have to be done with time-consuming numerical simulations. The optimized MPs show more than 4 times improvement in thermal sensitivity compared to previous demonstrations, thanks to the high thermal resistance and temperature sensitivity achieved using the thermomechanical model. The demonstrated theoretical analysis and thermomechanical optimization methods for the MPs are critical for the development of the next-generation zero-power IR sensors specifically designed for applications that require ultra-sensitive IR detection capability without compromising their sensor size, weight and power consumption. [2021-0231]
This paper reports on zero standby power human presence detectors based on an optimized micromechanical photoswitch (MP) with a metasurface-enhanced long wavelength infrared (LWIR) absorber, increased thermal sensitivity, reduced bias voltage, and a wide field-of-view. The reported device shows the capability of detecting a human body around 2.65 m and human hand around 1 m distance using low bias voltages without using any focal lenses. Existing wireless motion detectors based on pyroelectric IR sensors consume ∼100 μW power on standby continuously and produce frequent false alarms due to non-relevant objects (such as moving cars and falling leaves), which inevitably drains the battery in a relatively short period of time (typically less than a year). The demonstrated zero-power sensor here exploits the LWIR energy emitted from a human body for true presence detection without consuming any electrical power on standby. The first experimental demonstration of human body detection with vacuum packaged MP at a distance comparable to commercial motion detectors is enabled by the optimization of an MP in terms of thermomechanical performance (thermal sensitivity ∼1.5 nm/nW, stiffness ∼0.2 nN/nm, and threshold ∼10 nW) and IR absorption (η > 60% in λ = 6-14 μm, field-of-view ∼110 °). The new broadband LWIR metasurface absorbers improve the structural symmetry of MP by matching the material stacks of reflecting and absorbing heads. This improvement allows the MP to work with lower voltage bias thus, making it compatible with low-power electronics.