Sung-Wan Hong

Sung-Wan Hong

Auto-generated profile, based on publicly available information

Sung-Wan Hong

Seoul National University

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 January 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
YHYeunhee Huh
Yeunhee Huh
SHSung-Wan Hong
Sung-Wan Hong
GCGyu-Hyeong Cho
Gyu-Hyeong Cho
A dual-path step-down converter (DPDC) is presented for achieving high power efficiency in the mobile power management ICs (PMICs). Adopting a hybrid structure using one inductor and one flying capacitor, the proposed DPDC supplies a load current via two parallel paths, relieved an intrinsic problem of the conventional buck converter (CBC) topology, which is a significant power loss from a large DCR of the inductor (RDCR). Therefore, DPDC achieves a high power efficiency and thus also reduces the heating problem, which is another critical issue in the mobile set. Moreover, DPDC can shrink the volume of the PMIC set with a low manufacturing cost by alleviating an RDCR specification of the inductor. In this paper, although a 250 mΩ of large RDCR inductor is used for our measurements, a 96.2% of peak efficiency was achieved and the power loss of total parasitic resistances can be reduced to up to 30% of that of CBC. Moreover, according to our measurement plots, it is verified that DPDC achieves the efficiency notably higher not only in a wide load current (ILOAD) range but also in a wide conversion ratio (VOUT/VIN) range, compared to CBC.

20 December 2017 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
KYKye-Seok Yoon
Kye-Seok Yoon
SHSung-Wan Hong
Sung-Wan Hong
GCGyu-Hyeong Cho
Gyu-Hyeong Cho
This paper presents a double pile-up resonance energy harvesting circuit that efficiently and simultaneously extracts energy from a piezoelectric transducer (PZT) and a thermoelectric generator. The proposed harvester operates in a double pile-up mode (DPM) to efficiently extract energy from PZT with the enhanced damping force, resulting in a 1452% improvement in power extraction, which is the best performance among the state-of-the-art works. The harvester also operates in a boost converter mode (BCM) without an additional power switch, achieving 75% conversion efficiency at 450-μW output power. With a single-shared inductor, a simple control scheme enables the harvester to operate in both DPM and BCM by time-multiplexing method, consuming a low quiescent current of 240 nA. The prototype chip fabricated in a 0.18-μm BCD occupies an area of 1.5 mm x 1 mm, and it was tested with a 20-nF PZT product (PPA-1001) vibrated by a shaker (Type 4810).

18 June 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
WJWoojoong Jung
Woojoong Jung
SSSe-Un Shin
Se-Un Shin
SHSung-Wan Hong
Sung-Wan Hong
SYSung-Min Yoo
Sung-Min Yoo
TKTae-Hwang Kong
Tae-Hwang Kong
Hyung-Min LeeHyung-Min Lee
Hyung-Min Lee
This paper proposes a loop-free auto-calibration technique for self-balancing of flying capacitors in a three-level DC–DC buck converter. The proposed converter utilizes a dual- path power stage with balancing switches that adaptively short flying capacitors at de-energizing phases. Thus, the dual-path three-level converter ensures that flying capacitor voltages are self-balanced at half the input voltage without using additional feedback calibration loops, leading to robust operation and competitive efficiencies. The prototype was fabricated in 0.13-μm CMOS BCD process and adopted two flying capacitors of 4.7 μF each and an inductor of 10 μH with a DC resistance of 128 mA. When an 8 V input was converted to a 3 V output voltage with a load current of 400 mA, the measured efficiency was 88.6% at 800 kHz switching, while flying capacitors are automatically balanced.

18 November 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SSSe-Un Shin
Se-Un Shin
SHSung-Wan Hong
Sung-Wan Hong
Hyung-Min LeeHyung-Min Lee
Hyung-Min Lee
GCGyu-Hyeong Cho
Gyu-Hyeong Cho
This paper proposes a new boost converter topology called dual-path step-up DC-DC converter (DPUC). Unlike the conventional boost converter (CBC), the DPUC has a hybrid structure using one inductor and one flying capacitor to make dual current delivery paths. This allows continuous current delivering to the output, reducing both the DC level of the inductor current and the output voltage ripple. Therefore, the DPUC has higher efficiency and smaller output voltage ripple than those of CBC. In addition, the feedforward characteristic of the flying capacitor can alleviate the effect of RHP-zero that degrades the transient response. Even with the inductor DCR of 200mΩ, the DPUC achieves a high efficiency of 95.2% and a small ripple of up to 15mV.

3 December 2018 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
KKKi-Duk Kim
Ki-Duk Kim
Hyung-Min LeeHyung-Min Lee
Hyung-Min Lee
SHSung-Wan Hong
Sung-Wan Hong
GCGyu-Hyeong Cho
Gyu-Hyeong Cho
A non-inverting buck-boost converter with state- based current control is proposed for Li-ion battery management. Unlike conventional multi-mode control in buck-boost converters, our control scheme utilizes a state controller with a single-level error current and a state checking clock to define the operation mode at every cycle. The state-based buck-boost (S3B) converter enables seamless mode transition and stable output regulation with fixed interleaving patterns even when input and output voltages are similar, ensuring robust mode change with inherent hysteresis. The prototype IC was fabricated in 0.18-μm BCD process and achieved 90.9% efficiency with 1.1-A maximum load current capability at 1-MHz switching frequency.

11 August 2020 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
SHSung-Wan Hong
Sung-Wan Hong
This article proposes a current-mode (CM) receiver for a wireless power transfer (WPT) application that receives both power and data from the transceiver. The proposed CM receiver decreases the voltage stress applied to transistors to store a larger amount of power in its LC tank, and this charges the battery without any residual power. Accordingly, the receiver achieves the highest maximum receiver efficiency of 92.6% among the state-of-the-art CM receivers at an input power of 10.89 mW. The proposed CM receiver receives data along with the power by using energy-shift keying (ESK), which is the proposed data transfer method for the CM receiver. Due to ESK, the receiver achieves a maximum data rate of 100 kb/s while consuming negligible power for receiving the data. A prototype chip fabricated in a 180-nm CMOS process occupied an area of 0.43 mm × 0.49 mm, and a receiver coil was implemented as a printed spiral coil with dimensions of 6 mm × 6 mm.