28 February 2017 in Physics of Plasmas
The thin membrane that holds the capsule in-place in the hohlraum is recognized as one of the most significant contributors to reduced performance in indirect drive inertial confinement fusion (ICF) experiments on the National Ignition Facility. This membrane, known as the “tent,” seeds a perturbation that is amplified by Rayleigh-Taylor and can rupture the capsule. A less damaging capsule support mechanism is under development. Possible alternatives include the micron-scale rods spanning the hohlraum width and supporting either the capsule or stiffening the fill-tube, a larger fill-tube to both fill and support the capsule, or a low-density foam layer that protects the capsule from the tent impact. Experiments are testing these support features to measure their imprint on the capsule. These experiments are revealing unexpected aspects about perturbation development in indirect drive ICF, such as the importance of shadows coming from bright spots in the hohlraum. Two dimensional and 3D models are used to explain these features and assess the impact on implosion performance. Experiments and modeling suggest that the fill-tube supported by a perpendicular rod can mount the capsule without any additional perturbation beyond that of the fill tube.
18 May 2023 in Physical Review Letters
The hyperfine interval in atomic hydrogen was measured using Ramsey spectroscopy with a thermal beam cooled to cryogenic temperatures. The measured value is 177 556 838.87(85) Hz, which represents the most precise determination of this interval to date. The hyperfine interval and the hyperfine interval can be combined to give the quantity , which mostly eliminates uncertainty due to nuclear structure effects and is well described by bound-state quantum electrodynamics. Using the value of from this work gives a value of , which is in agreement with the theoretical value of .
1 May 2018 in Physics of Plasmas
High-mode perturbations and low-mode asymmetries were measured in the deceleration phase of indirectly driven, deuterium gas filled inertial confinement fusion capsule implosions at convergence ratios of 10 to 15, using a new “enhanced emission” technique at the National Ignition Facility [E. M. Campbell et al., AIP Conf. Proc. 429, 3 (1998)]. In these experiments, a high spatial resolution Kirkpatrick-Baez microscope was used to image the x-ray emission from the inner surface of a high-density-carbon capsule's shell. The use of a high atomic number dopant in the shell enabled time-resolved observations of shell perturbations penetrating into the hot spot. This allowed the effects of the perturbations and asymmetries on degrading neutron yield to be directly measured. In particular, mix induced radiation losses of ∼400 J from the hot spot resulted in a neutron yield reduction of a factor of ∼2. In a subsequent experiment with a significantly increased level of short-mode initial perturbations, shown through the enhanced imaging technique to be highly organized radially, the neutron yield dropped an additional factor of ∼2.
1 July 2018 in Physics of Plasmas
Hydrodynamic instability growth of capsule support membranes (or “tents”) has been recognized as one of the major contributors to the performance degradation in high-compression plastic capsule implosions at the National Ignition Facility (NIF) [E. M. Campbell et al., AIP Conf. Proc. 429, 3 (1998)]. The capsules were supported by tents because the nominal 10-μm diameter fill tubes were not strong enough to support capsules by themselves in indirect-drive implosions on NIF. After it was recognized that the tents had a significant impact of implosion's stability, new alternative support methods were investigated. While some of these methods completely eliminated tent, other concepts still used tents, but concentrated on mitigating their impact. The tent-less methods included “fishing pole” reinforced fill tubes, cantilevered fill tubes, and thin-wire “tetra cage” supports. In the “fishing pole” concept, a 10-μm fill tube was inserted inside 30-μm fill tube for extra support with the connection point located 300 μm away from the capsule surface. The cantilevered fill tubes were supported by 12-μm thick SiC rods, offset by up to 300 μm from the capsule surfaces. In the “tetra-cage” concept, 2.5-μm thick wires (carbon nanotube yarns) were used to support a capsule. Other concepts used “polar tents” and a “foam-shell” to mitigate the effects of the tents. The “polar tents” had significantly reduced contact area between the tents and the capsule compared to the nominal tents. In the “foam-shell” concept, a 200-μm thick, 30 mg/cc SiO2 foam layer was used to offset the tents away from the capsule surface in an attempt to mitigate their effects. These concepts were investigated in x-ray radiography experiments and compared with perturbations from standard tent support. The measured perturbations in the “fishing pole,” cantilevered fill tube, and “tetra-cage” concepts compared favorably with (were smaller than) nominal tent perturbations and were recommended for further testing for feasibility in layered DT implosions. The “polar tents” were tested in layered DT implosions with a relatively-stable “high-foot” drive showing an improvement in neutron yield in one experiment compared to companion implosions with nominal tents. This article reviews and summarizes recent experiments on these alternate capsule support concepts. In addition, the concept of magnetic levitation is also discussed.
1 August 2018 in Physics of Plasmas
Hydrodynamic instabilities and asymmetries are a major obstacle in the quest to achieve ignition at the National Ignition Facility (NIF) as they cause pre-existing capsule perturbations to grow and ultimately quench the fusion burn in experiments. This paper reviews the development of two new experimental techniques to measure high-mode instabilities and low-mode asymmetries in the deceleration phase of indirect drive inertial confinement fusion implosions. In the first innovative technique, self-emission from the hot spot was enhanced with an argon dopant to “self-backlight” the shell in-flight, imaging the perturbations in the shell near peak velocity. Experiments with pre-imposed two-dimensional perturbations showed hydrodynamic instability growth of up to 7000× in areal density. These experiments discovered unexpected three-dimensional structures originating from the capsule support structures. These new 3-D structures became one of the primary concerns for the indirect drive ICF program that requires their origin to be understood and their impact mitigated. In a second complementary technique, the inner surface of the decelerating shell was visualized in implosions using x-ray emission of a high-Z dopant added to the inner surface of the capsule. With this technique, low mode asymmetry and high mode perturbations, including perturbations seeded by the gas fill tube and capsule support structure, were quantified near peak compression. Using this doping method, the role of perturbations and radiative losses from high atomic number materials on neutron yield was quantified.
1 August 2018 in Physics of Plasmas
In indirectly driven Inertial Confinement Fusion implosions conducted on the National Ignition Facility (NIF), the imploding capsule is supported in a laser-heated radiation enclosure (called a “hohlraum”) by a pair of very thin (∼15–45 nm) plastic films (referred to as a “tent”). Even though the thickness of these tents is a small fraction of that of the spherical capsule ablator (∼165 μm), both numerical simulations as well as experiments indicate that this capsule support mechanism results in a large areal density (ρR) perturbation on the capsule surface at the contact point where the tent departs from the capsule. As a result, during deceleration of the deuterium-tritium (DT) fuel layer, a jet of the dense ablator material penetrates and cools the fuel hot spot, significantly degrading the neutron yield (resulting in only ∼10%–20% of the unperturbed 1-D yield). In this article, we present a hypothesis and supporting design simulations of a new “polar contact” tent support system, which reduces the contact area between the tent and the capsule and results in a significant improvement in the capsule performance. Simulations predict a ∼70% increase in neutron yield over that for an implosion with a traditional tent support. An initial demonstration experiment was conducted on the NIF and produced highest ever recorded primary DT neutron yield among all layered DT implosions with plastic ablators on the NIF, though more experiments are needed to comprehensively study the effect of the polar tent on implosion performance.