Long-term electrochemical performance of polymeric precursor-derived films of LaCoO 3 doped with Ca 2+ (LCC), instead of the larger Sr 2+ which segregates at the electrode surface forming oxides/hydroxides, was investigated in the present study. It was determined that pre-calcination at 800 °C (LCC02-800) resulted in a higher electrochemical performance but a poorer long-term stability than those pre-calcined at 700 °C (LCC02-700) or 900 °C (LCC02-900). Increasing Ca 2+ content (LCC04-800) enhanced the initial electrochemical performance slightly, while causing a much poorer long-term stability. Microstructural evolution analyses revealed that, although it had some impact on the initial and long-term performance of LCC electrodes, it was not the strongest influence. It was determined via XPS analyses that formation of CaO and CaO + La 2 O 3 layers at the LCC02-800 and LCC04-800 surfaces, respectively, accompanied by a decrease in the relative amounts of adsorbed oxygen species (corresponding to surface oxygen vacancies) caused a faster performance degradation in these samples than those pre-calcined at 700 or 900 °C. Eventually, only the surface cation ratio of LCC02-700 became close to the theoretical one after long-term operation.
Laser-induced graphene (LIG) is a scalable and cost-effective approach to fabricating carbon-based conductive materials for next-generation flexible electronics. Here, we report the synthesis of LIG by CO2 laser engraving of polyimide (PI) films, followed by doping with polyethylenimine (PEI). LIG powder was dispersed in a terpineol-ethanol-ethyl cellulose mixture, doped with 21.5 wt % PEI, and deposited as a thick film on a glass substrate using stencil-assisted application. Electrical conductivity measurements showed an increase from ∼20.8 S/m for LIG-only ink to 40 S/m after PEI doping, representing nearly a 2-fold enhancement attributed to increased electron carrier density and a Fermi level shift toward n-type behavior. Comprehensive characterization was performed to assess structural, morphological, and chemical modifications induced by doping. Scanning Electron Microscopy (SEM) confirmed the preservation of a porous, wrinkled graphene-like morphology. Energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FTIR) showed the successful incorporation of nitrogen. Raman spectroscopy revealed increased defect density and a Fermi level shift characteristic of n-type doping, while X-ray Diffraction (XRD) analysis showed reduced crystallinity and the formation of an amorphous phase. This work demonstrates that PEI not only modifies LIG chemically but also provides structural versatility, highlighting its potential for integration into real-world applications such as flexible and printed electronics. The combination of laser-assisted synthesis and polymer doping offers a practical route to the development of carbon-based materials.
Wearable thermoelectric generators are sustainable devices that generate electricity from body heat to provide a continuous power supply for electronic devices. In healthcare, they are particularly valuable for powering wireless devices that transmit vital health signals, where maintaining an uninterrupted power source is a significant challenge. However, these generators are prone to failure over time or due to mechanical damage caused by mechanical stress or environmental factors, which can lead to the loss of critical healthcare data. To address these issues, the integration of self-healing capabilities alongside flexibility and longevity is essential for their reliable operation. To our knowledge, this review is one of the first to look in depth at self-healing materials specifically designed for wearable thermoelectric generators. It explores the latest innovations and applications in this field highlighting how these materials can improve the reliability and lifetime of such systems.
Silicone polymers have various applications such as sensors, energy harvesters, soft robotics, prosthetics and implants. Ecoflex has become one of the most remarkable silicone polymers due to its special mechanical properties which include extreme stretchability and biocompatibility. In recent years, interest in porous silicone elastomers has increased in order to improve the absorption, flexibility and chemical activity of the material by increasing the surface area. In this study, porous Ecoflex 00-30 silicone elastomer material was prepared by using the low-cost sugar molding technique and its mechanical, optical and surface properties were investigated. In addition, we report on the influence of pore size on these properties of Ecoflex. Our results demonstrate that the Ecoflex material, which has a porous structure, has a more flexible structure. We have observed that the Ecoflex’s stretchability increased with pore size, especially in the 420–850 μm range.
The rapid and sensitive detection of nitroaromatic explosives is of paramount importance for both security and environmental monitoring. In this study, a label-free chemiresistive sensor based on laser-induced graphene (LIG) was developed for the selective detection of 2,4-dinitrotoluene (DNT). LIG films were directly fabricated on polyimide substrates via a single-step laser writing process, resulting in porous and conductive surfaces without additional modification. The structural, chemical, and electrical properties of the fabricated materials were comprehensively evaluated using scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS). The electrical properties were characterized by current–voltage (I–V) measurements using a Kelvin (pseudofour-point) configuration. SEM revealed a porous morphology formed during laser scribing, while XRD and Raman spectroscopy confirmed multilayer graphene (∼5 layers) with relatively low defect density. FTIR spectroscopy indicated residual oxygen-containing functional groups, and XPS verified DNT adsorption. The fabricated films exhibited a uniform electrical conductivity of 1545 S/m. By employing these films, a chemiresistive sensor was developed, which demonstrated a response toward DNT, achieving an estimated detection limit (LOD) of 3.79%, corresponding to 2.4 × 10–9 M. Strong selectivity was observed against structurally related interferents such as nitrotoluene, toluene, and ethanol. These results demonstrated that LIG-based flexible sensors provide a low-cost, scalable, and selective platform for explosive detection with promising applications in security and environmental monitoring.
Conductive polymer PEDOT:PSS is widely used in flexible electronics; however, the structural and electronic impacts of secondary doping remain poorly understood at the molecular level. In this study, we employ a dual-spectroscopy strategy—x-ray Photoelectron Spectroscopy (XPS) and Electron Paramagnetic Resonance (EPR)—to elucidate how ethylene glycol (EG) and dimethyl sulfoxide (DMSO) modulate the structure and charge transport properties of PEDOT:PSS films. While DMSO facilitates benzoid-to-quinoid transitions and supports polaron organization, EG promotes partial PSS removal and film morphology refinement. Spectroscopic analysis revealed a direct correlation between secondary doping-induced structural reordering and electronic structure characteristics, resulting in conductivity enhancements exceeding 400-fold relative to pristine PEDOT:PSS. By directly linking spectroscopic signatures with electrical performance, this work provides a molecular-level perspective on secondary doping effects, offering a rational basis for designing next-generation conductive polymer systems.