Strategies have been tailored to enhance electro-active material capacities and the cycle lives of sodium-ion batteries. Amongst the available electrode materials, metal–organic framework derived anode materials have begun to stand out because of their versatile compositions, structures, and textures, leading to high specific surface areas and more active electrochemical reaction sites. Herein, Ni-MOF is first prepared from a bio-available organic linker, namely gallic acid, in a benign solvent (water). Then a nickel sulfide/carbon (NiS/C) composite is synthesized via concurrent sulfuration and carbonization under nitrogen flow at 600 °C. Carbon-encapsulated NiS particles are formed, in which the carbon framework both prevents the volume expansion of NiS during discharge and also gives rise to higher conductivity. The resulting NiS/C composite is tested as a potential anode material for sodium-ion batteries and it delivered a capacity of around 208 mA h g−1 at a current density of 1475 mA g−1 after 500 charge/discharge cycles. The Na+-ion diffusion rate is calculated through Warburg impedance analysis, and values of 1.8 × 10−16 and 3.5 × 10−15 S cm−1 are obtained initially and after cell operations are terminated, respectively.
9 January 2020 in Journal of the Electrochemical Society
Long-term electrochemical performance of polymeric precursor-derived films of LaCoO 3 doped with Ca 2+ (LCC), instead of the larger Sr 2+ which segregates at the electrode surface forming oxides/hydroxides, was investigated in the present study. It was determined that pre-calcination at 800 °C (LCC02-800) resulted in a higher electrochemical performance but a poorer long-term stability than those pre-calcined at 700 °C (LCC02-700) or 900 °C (LCC02-900). Increasing Ca 2+ content (LCC04-800) enhanced the initial electrochemical performance slightly, while causing a much poorer long-term stability. Microstructural evolution analyses revealed that, although it had some impact on the initial and long-term performance of LCC electrodes, it was not the strongest influence. It was determined via XPS analyses that formation of CaO and CaO + La 2 O 3 layers at the LCC02-800 and LCC04-800 surfaces, respectively, accompanied by a decrease in the relative amounts of adsorbed oxygen species (corresponding to surface oxygen vacancies) caused a faster performance degradation in these samples than those pre-calcined at 700 or 900 °C. Eventually, only the surface cation ratio of LCC02-700 became close to the theoretical one after long-term operation.
8 June 2023 in The Journal of Physical Chemistry C
The electrical and NO2 sensing properties of a series of porphyrin derivatives (PPC12, PPC16, ZnPPC12) were studied within wide temperature range from 293 to 423 K under the N2 gas flow and in the frequency range from 1 kHz to 1 MHz for ac electrical measurements. The dc conductivities and the activation energies were found to be in the range of 10−13−10−12 S cm−1 at the room temperature and 0.46–1.03 eV respectively. The increased C number in the alkyl chain and addition of metal ion to the porphyrin causes a decrease in the conductivity. The ac conductivity was well represented by the power law form Aωs. The s parameter depending on temperature was varied 0.79–1.2. The conduction mechanism for all porphyrins could be related to small polaron tunneling (SPT) model. As an application, the NO2 sensing properties of ZnPPC12 were investigated depending on temperature.
A series of thin Pt-Co films with different metal ratios were deposited by using the sequential cosputtering directly on a commercial hydrophobic carbon paper substrate at room temperature and in ultra-high vacuum (UHV) conditions. Their electrocatalytic properties toward the oxygen reduction reaction were investigated in 0.5 M H2SO4 solution by means of cyclic voltammetry (CV) and linear sweep voltammetry (LSV) on rotating disc electrode (RDE). The results showed that Pt particles, deposited by dc-magnetron gun, surround the large Co-clusters deposited by rf-magnetron gun. In addition, the increase of Co content led to an increase in the electrochemical active surface area (EASA) from 23.75 m2/gPt to 47.54 m2/gPt for pure Pt and Pt:Co (1:3), respectively, which corresponded the improvement of the utilization of Pt by a factor of 1.91. This improvement indicated that the sequential magnetron cosputtering was one of the essential technique to deposit homogeneous metal clusters with desirable size on the gas diffusion layer by adjustment plasma parameters.