1 March 2023 in Journal of Structural Engineering
Many numerical simulation methods, such as finite-element analysis, were originally formulated to run serially or in parallel on central processing units (CPUs). However, computer engineering has seen a paradigm shift toward massive parallelism using graphics processing units (GPUs), which have become the default accelerators in many data-driven scientific disciplines outside of civil engineering. This state-of-the-art review highlights the challenges and practicalities of GPU-accelerating nonlinear dynamic analyses for civil structural problems. To demonstrate the feasibility of a fully GPU-accelerated finite-element analysis, a GPU-based program for linear-elastic dynamic analysis was implemented, where all stages of the analysis were ported to the GPU. Observed speedups were 115 times that of an equivalent CPU-driven analysis for model degrees of freedom (dof). Importantly, the computational time for the assembly and update levels of the analyses were nearly independent of the number of dof. High-resolution simulations of complex structures can be computationally expensive, but these results and advances in other fields suggest that some levels of the finite-element analysis of civil structures could be accelerated using GPUs at increased model resolution with little increase in computational cost, demonstrating the potential for GPU-accelerated computing. However, compared to other GPU-accelerated finite-element analysis applications, the dynamic analysis of civil structures is subject to unique challenges that need to be addressed before GPU acceleration can be fully realized. Aspects of simulating the response of civil structures considering nonlinear response under extreme loading may not be immediately amenable to GPU acceleration; e.g., the use of many differing element formulations within a model, potential for inelastic response and varying degrees of nonlinearity across elements, and traditional reliance on implicit integration schemes with direct solvers. The shift to GPUs is part of a larger movement toward specialized hardware using fine-grained parallelism, and structural engineers need to address these challenges as these emerging technologies become more prevalent.
27 July 2020 in Earthquake Engineering & Structural Dynamics
1 December 2021 in Journal of Structural Engineering
Strongback-braced frames employ an essentially elastic truss, or strongback, that defines an elastic load path to redistribute seismic demands and mitigate the formation of story mechanisms. However, unlike the forces from traditional capacity design—which assumes that inelastic response limits the earthquake-induced forces—design forces in the strongback arise from a nonlinear first mode and near-elastic higher-mode response, because the strongback is designed to remain elastic in every mode. A design method using modal pushover analysis, which combines the response from pushover analyses in multiple modes, can estimate the magnitude and distribution of the force demands in the first and higher modes, including inelastic response. The existing modal pushover analysis procedure is simplified and applied to the design of the strongback in strongback-braced frames. Accounting for only the first mode of response resulted in estimates below the 16th percentile of force demands extracted from nonlinear dynamic analysis. However, a modal pushover approach using multiple modes resulted in improved estimates able to represent both the distribution and magnitude of the peak force demands from nonlinear dynamic analysis of eight- and four-story strongback-braced frames with buckling-restrained braces, while maintaining the conceptual simplicity of nonlinear static analysis procedures.
1 January 2023 in Journal of Waterway, Port, Coastal, and Ocean Engineering
Gathering data for cascading seismic and tsunami events is difficult due to space constraints in existing experimental facilities, the application of scaling laws for both the fluid and structure, and limitations of computational software in simulating multiple hazards within the same analysis. To overcome these limitations, this study demonstrates the feasibility of a real-time hybrid simulation testing method to enhance wave–structure interaction simulations. While real-time hybrid simulations have been utilized for structures subjected to seismic events for decades, considerations for hybrid testing make its application to hydrodynamic problems challenging, including testing in wet or submersible environments and satisfying similitude time constraints. A cylindrical bridge pier specimen connected to a three-dimensional numerical bridge model was subjected to cascading seismic and tsunami events deploying a three-loop hardware architecture for real-time hybrid simulation. The domain was partitioned such that the wave–structure interaction on the bridge pier was physically tested in a wave flume and coupled to a numerical model of the remaining bridge components. To simulate existing damage, seismic loading was numerically applied to the hybrid model prior to the physical wave loading. Results illustrate that this simulation approach is feasible for future investigations using real-time hybrid simulation.
26 July 2023 in Earthquake Engineering & Structural Dynamics