Vyacheslav Rubel

Vyacheslav Rubel

Auto-generated profile, based on publicly available information

Vyacheslav Rubel

National University «Yuri Kondratyuk Poltava Polytechnic», Ukraine

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 April 2024 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
VRVictoriia Rubel
Victoriia Rubel
VRVyacheslav Rubel
Vyacheslav Rubel
TSTetiana Surzhko
Tetiana Surzhko
SGSergii Goshovskyi
Sergii Goshovskyi
This paper investigates the method of vibrating wave swabbing, which is used to stimulate the flow of liquid to the well. This method is known to generate mechanical waves in the soil that open microcracks and pores, increasing the flow of hydrocarbons. A carbonate reservoir with low permeability, which is quite common in the oil and gas industry, was considered as the study object. Therefore, the object of research was carbonate low-permeability reservoirs. After all, their low permeability makes the extraction of oil and gas from them a difficult task. As a result of processing, it was established that increasing the amplitude of pressure fluctuations contributes to increasing the efficiency of the vibration wave action, as the permeability of the reservoir increases more intensively, which was confirmed by the coefficient of determination, which was R2=0.92. And an increase in the frequency of oscillations, on the contrary, reduces it, because the depth of the effective zone of vibrational action decreases; in this case, the coefficient of determination was R2=0.81. To study the effect, a laboratory setup was designed that included a plunger device that generated fluid perturbations in a conditional borehole. The resulting elastic waves were measured by a manual contact vibrometer. Vibrating wave swabbing is a promising method for intensifying hydrocarbon production. The influence under investigation could be implemented in oil and gas fields with carbonate low-permeability reservoirs. This would lead to an increase in fluid production and improved efficiency of the oil and gas industry Досліджується метод віброхвильового свабування, який використовується для стимуляції припливу рідини до свердловини. Як відомо, метод полягає в тому, щоб створювати механічні хвилі в грунті, що розкривають мікротріщини та пори, збільшуючи при цьому приплив вуглеводнів. В якості об’єкту розглядався карбонатний колектор з низькою проникністю, який досить часто зустрічається в нафтогазовій промисловості. Тому об’єктом дослідження є карбонатні низькопроникні колектори. Адже їх низька проникність робить видобуток нафти та газу з них складним завданням. В результаті обробки було встановлено, що збільшення амплітуди коливань тиску сприяє підвищенню ефективності віброхвильової дії, так як проникність колектора зростає інтенсивніше, що і підтвердилося коефіцієнтом детермінації який склав R² = 0,92. А збільшення частоти коливань навпаки знижує, бо зменшується глибина ефективної зони віброхвильової дії, і в цьому випадку коефіцієнт детермінації склав R² = 0,81. Для дослідження впливу була розроблена лабораторна установка, яка включала пристрій-плунжер, який генерував збурення рідини в умовній свердловині. Пружні хвилі, що утворилися, вимірювалися ручним контактним віброметром. Віброхвильове свабування є перспективним методом для інтенсифікації видобутку вуглеводнів. Вплив, що досліджується може бути впроваджено на нафтових та газових родовищах з карбонатними низькопроникними колекторами. Це призведе до збільшення видобутку флюїду та підвищення ефективності роботи нафтогазовидобувної галузі

4 August 2023 in Technology audit and production reserves
Verified
Journal Article
Open access
PDF file
TSTetiana Surzhko
Tetiana Surzhko
MKMaksym Knysh
Maksym Knysh
YKYurij Kuzub
Yurij Kuzub
OKOleksandr Kruchkov
Oleksandr Kruchkov
VRVyacheslav Rubel
Vyacheslav Rubel
The object of the research is elastic plates located across the movement of the solution on the vibrosieve. The problem of uniform distribution of material on the surface of the sieve is considered, which is solved with the help of the design proposed in the work. Tensometry was used as a research method with subsequent processing of the results on an elector computer. In the course of the research, an analog-to-digital converter developed and manufactured at the Department of Mechanization of Construction Processes of the National University «Yuri Kondratyuk Poltava Polytechnic» (Ukraine) was used. As well as a computer with a free COM-1 port, «PROGRAM.EXE» software and a spreadsheet editor, strain gauges in the form of strain gauges with two pasted tensor resistors connected by a half-bridge circuit. The paper proposes a fundamentally new scheme of a vibrosieve with additional working bodies in the form of elastic plates located across the movement of the solution on the sieve. The elasticity and mass of the plates are selected in such a way that their oscillations during the operation of the vibrosieve exciter are close to resonance. At the same time, the mode of vibration of the vibrosieve itself is far beyond resonance. As a result, a higher-quality and energy-efficient cleaning of the washing liquid will be obtained. This is due to the fact that the proposed cleaning method has a number of features, in particular, dispersion of drilling fluid over the entire surface of the vibrosieve and maximum loading of the entire working surface of the sieve to avoid dead zones. Thanks to this, it is possible to obtain resonant oscillations. In comparison with known analogs that work in a resonant mode, this provides advantages in the cleaning of drilling mud. The amplitude of oscillations of elastic plates reaches 1.2–1.5 mm, which is significantly greater than the amplitude of oscillations of a vibrating table. In practice, it will be possible to use the proposed fundamentally new scheme of a vibrosieve with additional working bodies in the form of elastic plates that work in a resonant mode, as a way of supplementing vibrosieves that are in use or new when manufactured at manufacturers' factories.

21 October 2022 in Technology audit and production reserves
Verified
Journal Article
Open access
PDF file
VRViktoria Rubel
Viktoria Rubel
VRVyacheslav Rubel
Vyacheslav Rubel
JZJan Ziaja
Jan Ziaja
RYRoman Yaremiychuk
Roman Yaremiychuk
The object of research in the work is a mathematical model of the operation of a hydrodynamic well generator of the spring-valve type. The existing problem lies in the fact that vibrating wave swabbing differs from known methods of vibrating wave influence on the near-breakout zone of the formation in its ease of execution and, as a result, a much smaller range of equipment. At the same time, its effectiveness should not be inferior to known methods because the treatment of the formation is carried out by elastic low-frequency pressure fluctuations against the background of depression on the formation. Since the swab generator valve is, in fact, a hydrodynamic well generator (HWG) of the spring-valve type, the processes of pressure fluctuations in the considered devices will be similar. However, because of the review of HWG designs, the presence of a mathematical model describing the operation of rotor-type devices, and not valve type, was revealed. Despite the fact that the mathematical model takes into account all the main factors that determine the process of the HWG piston movement, this model cannot be used to describe the operation process of the swab generator valve. Due to the absence of a pulsating flow created at the wellhead by pumping units. Taking this fact into account, as well as taking into account the compressibility of the liquid passing through the valve, a new mathematical model was developed. It describes both the process of operation of a spring-valve type HWG operating in a well on pump-compressor pipes, and the operation of a swab generator valve that is lowered into a well on a rope. Thanks to this, it is possible to obtain the parameters of the oscillating system: geometric dimensions, inertial mass of moving parts, stiffness of the spring, coefficient of viscous friction between the piston and the valve body, as well as parameters of the working fluid: pressure, flow and its rheological properties. In comparison with the similarly known technology of vibration wave impact on a formation with known HWG, it provides such advantages as a higher speed of movement and frequency of oscillations of the moving end of the spring from the identified essential parameters of the oscillating system and the working fluid of the spring (100–1000 N/mm), consumption of working liquid (10–130 m3/h), valve opening pressure (1–7 MPa). This will make it possible to calculate a helical cylindrical compression spring made of round steel for its operation in the valve of the swab generator without collision of turns.

4 December 2023 in Technology audit and production reserves
Verified
Journal Article
Open access
PDF file
VRVictoriia Rubel
Victoriia Rubel
VRVyacheslav Rubel
Vyacheslav Rubel
The object of the study is a laboratory unit for inducing flow to the well using vibration wave draining in carbonate low-permeability reservoirs. Vibratory wave draining is a method used to stimulate flow draining to the well. The method is based on the fact that mechanical waves generated in the soil can cause the opening of microcracks and pores, which leads to an increase in the fluid flow. Vibratory wave scouring can be effectively used to increase fluid flow in low-permeability carbonate reservoirs. Carbonate reservoirs are a common type of reservoir in the oil and gas industry. They often have low permeability, which makes it difficult to extract fluid. With the help of the plunger device developed in the work, a fluid disturbance was created, thereby creating elastic waves in the conventional well (plastic pipe), which were measured using a manual contact vibrometer. This demonstrated the effectiveness of the vibratory method to increase the well productivity and helped to improve the permeability of the rocks, providing better access to challenge the influx of hydrocarbon products. It is shown that with a significant decrease in the permeability of the formation well zone (FWZ), the flow induction should be started only after the restoration works. Otherwise, the well will be significantly hydrodynamically imperfect due to the quality of the reservoir opening, and the flow of production into the well will occur only through a few separate areas of the reservoir with relatively high permeability, which will lead to uneven production of the reservoir and low return of hydrocarbons. Therefore, it is advisable to use the developed method of influencing the productive layer in low-permeability rocks, such as carbonates with layers of clay, siltstones, argillites, and others, with low formation pressures. The obtained results are based on the generation of vibrations that are transmitted to the wellbore. These vibrations can help break up contaminants and fines in carbonate rocks, facilitating the release of hydrocarbon products and improving permeability.