31 August 2022 in Eastern-European Journal of Enterprise Technologies
When studying the construction of oil and gas wells, it was found that the volume of drilling wells with abnormally low reservoir pressures increases over the years. This is due to significant difficulties such as a large absorption of drilling mud, possible clogging of a productive reservoir with drilling mud, and a failure to obtain the expected effect. These complications can be prevented by using gas-liquid mixtures as drilling mud, which have a number of advantages compared to washing liquids and make it possible to eliminate the above-mentioned negative phenomena. When opening productive horizons at low anomaly coefficients, foams must be used to flush wells. It has been established that at present in the practice of drilling oil and gas wells with foam there is no equipment that makes it possible to form foam with certain specified structure and dispersion. The use of a modernized foam generator for the preparation of foam has been proposed. To study the foaming process, computer modeling was carried out, with the help of which the processes that take place during the movement of flows of liquid, gas, and gas-liquid mixture along the foam generator were investigated, namely the distribution of pressure and speed in the longitudinal cross-section of the foam generator under changing boundary conditions, that is, at a pressure in the supply pipe of 10 and 7.5 MPa. Computer studies have confirmed the possibility of using an improved foam generator design to increase the efficiency of foaming. The results could be the basis for the development of foam generators and their experimental and industrial research and testing.
4 August 2023 in Technology audit and production reserves
The object of the research is elastic plates located across the movement of the solution on the vibrosieve. The problem of uniform distribution of material on the surface of the sieve is considered, which is solved with the help of the design proposed in the work. Tensometry was used as a research method with subsequent processing of the results on an elector computer. In the course of the research, an analog-to-digital converter developed and manufactured at the Department of Mechanization of Construction Processes of the National University «Yuri Kondratyuk Poltava Polytechnic» (Ukraine) was used. As well as a computer with a free COM-1 port, «PROGRAM.EXE» software and a spreadsheet editor, strain gauges in the form of strain gauges with two pasted tensor resistors connected by a half-bridge circuit. The paper proposes a fundamentally new scheme of a vibrosieve with additional working bodies in the form of elastic plates located across the movement of the solution on the sieve. The elasticity and mass of the plates are selected in such a way that their oscillations during the operation of the vibrosieve exciter are close to resonance. At the same time, the mode of vibration of the vibrosieve itself is far beyond resonance. As a result, a higher-quality and energy-efficient cleaning of the washing liquid will be obtained. This is due to the fact that the proposed cleaning method has a number of features, in particular, dispersion of drilling fluid over the entire surface of the vibrosieve and maximum loading of the entire working surface of the sieve to avoid dead zones. Thanks to this, it is possible to obtain resonant oscillations. In comparison with known analogs that work in a resonant mode, this provides advantages in the cleaning of drilling mud. The amplitude of oscillations of elastic plates reaches 1.2–1.5 mm, which is significantly greater than the amplitude of oscillations of a vibrating table. In practice, it will be possible to use the proposed fundamentally new scheme of a vibrosieve with additional working bodies in the form of elastic plates that work in a resonant mode, as a way of supplementing vibrosieves that are in use or new when manufactured at manufacturers' factories.
19 May 2025 in Technology audit and production reserves
The object of research is the process of air saturation of the flushing fluid using a multi-nozzle foam generator in the circulation systems of drilling rigs. One of the most problematic areas in the known designs of foam generators is the insufficient efficiency of air saturation of the fluid, which is solved by the design proposed in the work. The design of a multi-nozzle foam generator is proposed by improving the mixing chamber. This design allowed to provide improved foam formation, more efficient air saturation of the flushing fluid, reduce the time of well development and increase the productivity of the device without changing the pressure and supply of fluid and air. During the study, computer mathematical modeling was used (in the Maple 9.5 software environment), a study of the dependence of air flow on pressure and fluid flow at nozzle diameters of 4 mm and 6 mm was performed. The studies considered graphical analysis to determine the optimal operating modes of the foam generator. An improved multi-nozzle foam generator with improved foaming efficiency, uniform saturation of the flushing fluid with air, reduced energy consumption and reduced well development time was obtained. This is due to the improvement of the design of the mixing chamber, which has a number of features. The proposed design provides intense turbulence, uniform mixing of the fluid with air, optimization of the geometric parameters of the nozzles and feed channels, as well as reduction of hydraulic losses in the foaming process. Thanks to this research, it is possible to obtain indicators that characterize the pattern of increasing air flow in proportion to increasing pressure. Compared with known analogues, the proposed foam generator, thanks to the variable geometric parameters of the mixing chamber and nozzles, allows to obtain foam mixtures with a wider range of properties. Such geometric changes provide better saturation of the fluid with air, create more intense turbulence, reduce hydraulic losses, and also increase the productivity and efficiency of well development.
29 August 2024 in Eastern-European Journal of Enterprise Technologies
The object of research is an element of equipment in a vibrating screen, which is an active working body in the form of a plate. The key element in the system of the flush purification unit is the vibrating screen. The basic design of the sieve does not allow the flush solution to be distributed evenly over the entire working surface. The concentration of drilling fluid in the central part of the equipment leads to premature abrasive wear and failure of the working element. Therefore, the structure of the vibrating screen needs to be improved in order to extend its service life. This task has been solved through the introduction of an active element to the structure for the redistribution of the solution through additional transverse vibrations. The use of such an active element is an important step for improving the quality and efficiency of the purification system, which could optimize production processes and reduce costs in industry. Taking into account transverse vibrations and calculating frequency parameters could help improve the design and use the vibrating screen more productively. An analysis of the frequencies of oscillations of the active element-plate for cleaning the flush liquid with a vibrating screen was performed and a comparison of the analytically obtained results with the simulation data using the finite element method in the COMSOL Multiphysics software was carried out. The results are the basis for designing vibrating screens, conducting experimental and industrial research, and testing the screens. Computer studies have confirmed the possibility of using the improved design of the vibrating screen. By comparing the results of the calculation and computer simulation, the error was determined to be within 5 %. The identified patterns could make it possible to select the plate oscillation frequencies depending on the known initial parameters, which would be useful for solving similar tasks.