1 January 2007 in Journal of Materials Science: Materials in Medicine
CDConceição Aparecida Matsumoto Dutra
Conceição Aparecida Matsumoto Dutra
1 January 2010 in Journal of Craniofacial Surgery
DSDaniela Micheline dos Santos
Daniela Micheline dos Santos
LBLisiane Cristina Bannwart
Lisiane Cristina Bannwart
+1
Implants in craniofacial reconstructions improve prostheses retention and stability, comfort, and safety for the patient. According to biomechanical principles, the treatment success regarding osseointegration maintenance depends on an adequate surgery technique associated to a retention system that provides favorable tension distribution to implants. Implants in the mastoid area are a very important aid for retention of auricular prostheses. Color stability of resin and silicone is an important factor for longevity of auricular prostheses, and the high degree of satisfaction of patients with head and neck defects receiving epithesial reconstruction in the maxillofacial region is demonstrated.
17 October 2011 in Gerodontology
doi: 10.1111/j.1741-2358.2011.00570.x Effect of disinfection and storage on the flexural strength of ocular prosthetic acrylic resins Objective: To evaluate the influence of chemical disinfection and storage duration on the flexural strength of acrylic resins commonly used to make ocular prostheses. Methods: A total of 260 samples were manufactured with N1 resin and colourless resin. Both resins were thermopolymerised using a microwave oven. Samples were stored and periodically disinfected and were divided into groups: control (no disinfection) (I), neutral soap (II), Opti-free (III), Efferdent (IV), 1% hypochlorite (V) or 4% chlorhexidine (VI). The flexural strength was measured before and after 60 and 120 days of storage. Data were analysed by anova and Tukey test (0.05). Results: The flexural strength of the N1 resin was higher than that for the colourless resin. There was a significant difference in the flexural strength before and after 60 and 120 days of storage with disinfection, regardless of the resin and disinfectant. Group I in the initial period exhibited greater flexural strength, with significant difference only in group VI after 120 days. Conclusion: It can be concluded that the flexural strength only changed after 120 days of storage for samples disinfected with chlorhexidine. However, all flexural strength values obtained herein were acceptable clinical limits for the acrylic resins.
30 March 2020 in Microscopy Research and Technique
10 September 2011 in Journal of Materials Science: Materials in Medicine
1 July 2010 in Journal of Craniofacial Surgery
BTBianca Piccolotto Tonella
Bianca Piccolotto Tonella
PCPaulo Sérgio Perri de Carvalho
Paulo Sérgio Perri de Carvalho
The aim of this study was to assess the stress distribution of the retention systems (screwed and cemented) for implant-supported fixed partial dentures by means of photoelastic method. Two models were made of photoelastic resin PL-2 with 2 implants (phi = 4.00 x 10 mm) located in the second premolar and molar region in each photoelastic model, varying the retention system (screwed and cemented). The implant-supported fixed partial dentures were standardized and made of Ni-Cr alloy. Axial and oblique (45 degrees) forces of 100 N were applied on the occlusal surface by means of a Universal Testing Machine (EMIC-DL 3000; São José dos Pinhais, Paraná, Brazil). The results were observed and photographed in the field of a circular polariscope and qualitatively analyzed with the aid of computer software (Adobe Photoshop, San Jose, CA). The screw retention system presented the highest number of fringes when the loads were applied on the premolar, pontic, and molar and showed this behavior in all load applications, under axial and oblique loads. It was concluded that there was a better stress distribution and lower magnitude of stress on the cemented implant-supported dentures, under axial and oblique loads. Oblique load caused an increase in stress concentrations in all the models.