9 November 2023 in IEEE Sensors Journal
In this paper, the authors propose a two-dimensional (2D), wide dynamic range, linear displacement sensor based on the microwave resonator principle. The sensor employs a cylindrical dielectric resonator (DR) proximity coupled to a pair of 50 Ω microstrip lines that are laid orthogonally over a microwave substrate. The DR is free to move on the substrate in the 2D space between the microstrips so that the coupling strength of the excited DR mode varies with the DR’s proximity to the microstrips. This variation in coupling strength can be measured in terms of the two-port scattering (S) parameters of the circuit, from which the DR’s displacement can be estimated. The above circuit operates at a fixed frequency determined by the resonant frequency of the particular mode of the DR. Initial one-dimensional (1D) analysis using the |S 21 | sensitivity of the DR displacement reveals a dynamic range of more than 23 mm for the horizontal, vertical and diagonal displacements. To enable full 2D scanning by differentiating the horizontal and vertical displacements, the |S 11 | and |S 22 | parameters are also taken into account in addition to |S 21 |. Note that in all the above measurements, the sensor’s operating frequency remains constant at 3.67 GHz which is the resonant frequency of the DR. Such single-frequency sensors are highly robust to frequency offsets and are also cost-effective in practical realisation compared to variable frequency sensors. This aspect as well as other performance parameters of the proposed sensor are compared with that of existing 2D sensors.
14 October 2025 in IEEE Sensors Letters
This letter presents, for the first time, a highly sensitive microwave sensor for linear displacement detection based on the split-in-frequency principle using a cylindrical dielectric resonator (CDR). The sensor consists of a stator (substrate with a rectangular slot) and a mover (CDR), where displacement is measured by tracking resonant frequency splitting induced by symmetry breaking. When the CDR is centered over the slot, the system exhibits a single transmission zero (f₀); any displacement breaks the symmetry, generating two distinct transmission zeros (Δf), which linearly correlate with displacement. Leveraging this mechanism, the sensor achieves an unprecedented sensitivity of 375 MHz/mm over a 0-3 mm range, the highest reported for split-in-frequency microwave resonator-based displacement sensors, while maintaining excellent linearity. A prototype is fabricated and experimentally validated using a VNA, confirming full-wave simulation (Ansys HFSS) results. Furthermore, real-time displacement estimation is implemented through an inverse regression model operating directly on frequency measurements, with provided regression matrices enabling immediate deployment in practical sensing applications.
2 January 2026 in IEEE Transactions on Instrumentation and Measurement
This paper reports the first dual-principle microwave displacement sensor, capable of operating in either frequency-shift or single-frequency amplitude-variation mode, thereby offering unprecedented flexibility for displacement measurement. The sensor consists of a metallic strip printed on a high-permittivity circular dielectric slab, forming a cylindrical dielectric resonator (CDR) positioned between two parallel microstrip transmission lines. A key feature is that the operating mode is selected simply by changing the orientation of the resonator relative to the feedlines, enabling effortless reconfiguration. In the frequency-shift mode (strip perpendicular to the feed lines), displacement is detected through variations in open-stub lengths on the feedlines, achieving 40 MHz/mm sensitivity over a 0–40 mm range. In the amplitude-variation mode (strip parallel to the feedlines), two resonances- strip and dielectric-resonator modes- are exploited, yielding sensitivities of 2 dB/mm (0–12 mm) and 1 dB/mm (0–17 mm), respectively. The sensor further exhibits a wide dynamic range in swept-frequency operation and simultaneous multi-resonance detection in fixed-frequency mode, with high agreement between simulations and measurements. The proposed design introduces a new class of reconfigurable resonator-based displacement sensors with strong potential for robotics, industrial automation, structural health monitoring, and aerospace vibration detection.
28 March 2026 in Sensors and Actuators A: Physical
1 April 2026 in IEEE Sensors Journal
This paper presents a non-invasive microwave sensor for detecting formalin using near-field analysis. A novel triple-oval resonating sensor is developed with a unique mirror pattern of identical top and ground structures to achieve high selectivity. Through the duality principle of the radiating element, the sensor measures the presence of formalin. A frequency shift of 50 MHz to 90 MHz is observed in the phase (I) and quadrature (Q) components measurements, enabling magnitude and phase analysis. The raw microwave signal was denoised and treated using the Chirp-Z Transform. Additionally, the fast Fourier transform is employed to extract spectral features, facilitating the precise identification of formalin presence. Classification algorithms categorize contamination levels, confirming accurate measurement and rapid assessment for food safety in real-time monitoring.
5 March 2026 in IEEE Sensors Journal
This paper presents the systematic design and characterization of a cylindrical dielectric resonator (CDR)-based displacement sensor operating under dual excitation modes. To begin with, the CDR is investigated through radar cross-section analysis to identify the natural resonant modes. Each mode is subsequently excited by using a simple microstrip feed line to evaluate its suitability for displacement sensing in terms of resonant frequency, sensitivity, and dynamic range. Numerical simulations identify the TE011+δ and HEM12δ modes are found to exhibit superior sensing capabilities compared to all other supported modes. Further, a transmission-mode sensor configuration is then proposed, wherein both modes are simultaneously excited using a pair of 180° aligned offset microstrip lines integrated within the same CDR structure, allowing to compare the sensitivity performance of the higher-order mode with respect to the fundamental mode. This dual-mode excitation enables the sensor to harness the complementary features of both modes simultaneously. Comprehensive full-wave simulations are carried out in HFSS to validate the concept, and a prototype is fabricated and experimentally characterized. The measured results show good agreement with simulations, confirming that the proposed sensor achieves a nearly threefold improvement in sensitivity with the higher-order mode, though at the expense of reduced dynamic range.