Asier Alonso

Asier Alonso

Auto-generated profile, based on publicly available information

Asier Alonso

CEIT , Paseo M. Lardizabal, 13, 20018, San Sebastían (Guipúzcoa), Spain

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 June 2011 in Vehicle System Dynamics
Verified
Journal Article
Closed access
AAA. Alonso
A. Alonso
JGJ. G. Giménez
J. G. Giménez
EGE. Gomez
E. Gomez
This paper deals with the modelling of yaw dampers and determining the influence of the modelling of this component on the results obtained when predicting the dynamic stability of a vehicle. The first part of the work analyses the influence of the yaw damper characteristics on railway dynamic stability. Following this, a physical model of the damper is developed which allows its performance to be reproduced accurately in the whole range of operating conditions the damper is envisaged to operate in. Once obtained, it was found that the computational cost of the model was relatively high. Therefore, a simplified model has been developed. The simplified model allows obtaining accurate results without excessively increasing the time required to perform the simulations. Analysing the results obtained with this model, it has been concluded that with respect to previous model based on conventional approaches, it improves the accuracy of dynamic calculation for the stability assessment. Also, it has been found that the accurate modelling of the yaw damper is critical when dealing with the vehicle's dynamic performance. In the last part of the paper, a special type of yaw damper was studied as well as its effect on the dynamic behaviour of the vehicle.

26 November 2010 in Vehicle System Dynamics
Verified
Journal Article
Closed access
AAA. Alonso
A. Alonso
JGJ. G. Giménez
J. G. Giménez
JNJ. Nieto
J. Nieto
Jordi VinolasJordi Vinolas
Jordi Vinolas
The air spring is one of the components that most affects vehicle comfort. This element usually makes up the main part of the secondary suspension, which introduces both stiffness and damping between the bogie and the car body. Therefore, a deep understanding of this element is necessary in order to study the comfort of a vehicle, the influence of different parameters and the ways to improve it. In this work, the effect of the air spring system on comfort is studied. To accomplish this, a typical pneumatic suspension composition is briefly studied as a first step. Then, the test bench developed to characterise air springs is described, presenting experimental results. Correlation of the results with some theoretical models is also addressed. Afterwards, the effect of the air spring system on comfort is analysed, and finally, improvements from introducing a variable area orifice in the pipe that joints the air spring and the surge reservoir are discussed.

8 February 2008 in Vehicle System Dynamics
Verified
Journal Article
Closed access
AAA. Alonso
A. Alonso
JGJ.G. Giménez
J.G. Giménez
This paper deals with the solution of the non-steady state wheel-rail contact problem. Firstly, the existing models are analysed and it is concluded that none of them have the computational efficiency and/or accuracy characteristics required to be used in a railway simulation programme. Following this, a new solution is proposed to the problem that allows obtaining sufficiently accurate results with a relatively low computational cost. During the development of the proposed method it has been assumed that only one type of creepage is variable with respect to the time. Further work is necessary to extend it to more general cases.

21 March 2007 in Vehicle System Dynamics
Verified
Journal Article
Closed access
AAA. Alonso
A. Alonso
JGJ. G. Giménez
J. G. Giménez
This article deals with the application of the FastSim algorithm to the solution of the tangential contact problem for non-elliptical contact areas. At first, the causes creating problems for the solution of non-hertzian contact areas with this algorithm shall be analyzed. Then, different currently existing methods shall be studied, analyzing their accuracy characteristics and computational cost to determine whether or not they are appropriate to use in dynamic simulations. Finally, a new strategy shall be proposed that, in the opinion of the authors, offers good characteristics of precision and computational cost.

23 May 2014 in Vehicle System Dynamics
Verified
Journal Article
Closed access
AAA. Alonso
A. Alonso
AGA. Guiral
A. Guiral
LBL. Baeza
L. Baeza
SISimon IWNICKI
Simon IWNICKI
The wheel–rail contact problem plays an important role in the simulation methods used to solve railway dynamics problems. As a consequence, many different mathematical models have been developed to calculate wheel–rail contact forces. However, most of them tackle this problem purely from a theoretical point of view and need to be experimentally validated. Such validation could also reveal the influence of certain parameters not taken into account in the mathematical developments. This paper presents the steps followed in building a scaled test-bench to experimentally characterise the wheel–rail contact problem. The results of the longitudinal contact force as a function of the longitudinal creepage are obtained and the divergences with respect to Kalker's simplified theory are analysed. The influence of lateral creepage, angular velocity and certain contaminants such as cutting fluid or high positive friction modifier is also discussed.

1 January 2006 in Vehicle System Dynamics
Verified
Journal Article
Closed access
AAA. Alonso
A. Alonso
JGJ. G. Giménez
J. G. Giménez
In the majority of railway dynamic simulator programs, the Hertz theory is used for solving the normal wheel–rail contact problem. This theory provides good results in the most common situations; however, its results are not satisfactory in situations such as the solution of non-elliptical contact areas, the multi-contact conditions and the transition from two to one contact area. In a previous paper, Alonso and Giménez [Alonso, A. and Giménez, J.G., 2005, A new method for the solution of the normal contact problem in the dynamic simulation of railway vehicles. Vehicle System Dynamics, 43, 149–160.] showed that the square root simplified theory (SRST) allows solving the normal contact problem for general undeformed distance profiles with enough accuracy. In this paper, the SRST method is modified in order to solve accurately multi-contact situations, including the union and separation of two contact areas. The results obtained are acceptably precise for most rail applications