Aakash Singh

Aakash Singh

Auto-generated profile, based on publicly available information

Aakash Singh

Electrical Engineering Department, IIT (BHU), Varanasi, India

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 May 2023 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
ASAakash Singh
Aakash Singh
VSVulavakayala Siva
Vulavakayala Siva
AKAvneet Kumar
Avneet Kumar
SSSantosh K Singh
Santosh K Singh
High step-up voltage conversion is required in renewable energy systems. This paper presents a non-isolated high step-up DC-DC converter based on active switched-inductors (ASL) with switched capacitor cells (SCC). The unique selling proposition of the proposed converter is division of input current which reduces the inductor size. In the proposed topology, the capacitor and diode are arranged in such a way that they interconnect the input to the load side for obtaining high step-up ratio. The main advantages of the converter are high step-up ratio at a low duty cycle with low switch stress and low component count. Operating principles, design equations, and device stress are included in this paper. Moreover, small-signal analysis and its bode plots are presented here. In addition, the loss distribution is critically investigated. Finally, to verify the theoretical study, a laboratory prototype is built and tested at different operating points in continuous conduction mode (CCM).

20 April 2023 in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
Verified
Journal Article
Closed access
VSVulavakayala Siva
Vulavakayala Siva
MRM. Raghuram
M. Raghuram
ASAakash Singh
Aakash Singh
SSSantosh K Singh
Santosh K Singh
Yam SiwakotiYam Siwakoti
Yam Siwakoti
This paper aims to reduce the ripple current in the inductor used in a Quasi Z-source Ultra Sparse Matrix Converter (QZSUSMC). The main limitations of the conventional Ultra Sparse Matrix Converter (USMC) are limited voltage gain $(\leq 0.866)$ and high common mode voltage (CMV). By integrating a quasi Z-source network in the DC link of USMC and providing a shoot-through (ST) state in a switching cycle, a voltage gain greater than unity can be achieved. Inductors are magnetised during the ST state and demagnetized during the nonshoot-through (NST) state. Hence with a proper arrangement of the ST and NST states, ripple in the inductor current can be minimised. In the proposed modulation, the total ST time is divided into six unequal parts and arranging them to minimize the inductor ripple current. in addition to it, proposed method also offers proper switching arrangements by using active vectors to attenuate peak-peak common mode voltage (CMV). As compared to the earlier reported methods, the proposed method produces a better inductor current ripple and a reduced peak of the CMV. Simulation and developed testing circuit results show the effectiveness of the proposed method.

25 March 2026 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
Priyabrata ShawPriyabrata Shaw
Priyabrata Shaw
ASAakash Singh
Aakash Singh
PGPriyabrat Garanayak
Priyabrat Garanayak
SSSantosh K Singh
Santosh K Singh
Achieving a very high voltage gain using a traditional boost DC-DC converter (TBDC) without resorting to extreme duty ratios remains a significant challenge. This paper proposes a novel family of single-switch Z-source DC-DC converters (ZSDCs), referred to as Super-Lift Z-source DC-DC Converters (SuLZSDCs), which leverage the super-lift technique to address this limitation. The integration of a super-lift cell not only enhances the voltage conversion ratio but also significantly reduces the voltage stress on the switching device. A comprehensive steady-state mathematical analysis is conducted to highlight the key features of the proposed topologies and is followed by a detailed comparison with existing Z-source converter configurations. Additionally, small-signal modelling of the enhanced SuLZSDC topology is carried out to analyze system dynamics and facilitate the design of a proportional–integral (PI) controller for output voltage regulation and stable closed-loop operation. To validate the theoretical findings and demonstrate the high-gain performance, a 400 W laboratory prototype is developed and tested. Experimental results under both steady-state and dynamic conditions confirm the effectiveness and practical feasibility of the proposed SuLZSDC topologies.

3 January 2024 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
VSVulavakayala Siva
Vulavakayala Siva
MRM. Raghuram
M. Raghuram
ASAakash Singh
Aakash Singh
SSSantosh K Singh
Santosh K Singh
The conventional ultra sparse matrix converter (USMC) attains a maximum voltage gain of 0.866, a crucial limitation of matrix converters. It can be overcome by integrating the impedance network with USMC. The primary focus of this article is to integrate switched boost network with USMC to improve the gain profile. This impedance network consists of semiconductor devices and energy storing elements. Controlling this impedance network without affecting the normal operation of USMC has remained a challenging task, which the authors have carefully handled in this article. This article investigates the load power factor effects on the overall voltage gain, which leads the converter to a nonzero discontinuous current mode. Further, this article deals with the total harmonic distortion dependency on the output frequency. In comparison to already reported converters, the proposed converter enhances the gain with minimum passive components. The simulation and experimental results (400 Hz load frequency) show that the proposed converter can boost the voltage gain greater than the unity with two passive elements.