This paper presents the design of an optimized Interval Type 2 Fuzzy Proportional Derivative Controller (IT2F-PDC) in cascade form for Rotary Inverted Pendulum (RIP) system. The parameters of the IT2F-PDC are optimised by using Genetic Algorithm (GA) and Particle Swarm Optimization (PSO). The goal is to balance the pendulum in upright unstable equilibrium position. The IT2F-PDC which is the extended version of conventional type 1 fuzzy logic controller, improves the control strategy by using the advantage of its footprint of uncertainty for the fuzzy membership function. The performance characteristics considered for the controller are steady state error, settling time, rise time, maximum overshoot, and control energy. Experimental and simulation results indicated that the effectiveness and robustness of the proposed GA- and PSO-based controllers on the RIP with respect to load disturbances, parameter variation, and noise effects have been improved over state-of-the-art method. However, the comparative results for simulation and experiment based on cascade IT2F-PDC indicate that GA-based IT2F-PDC has lower steady state error while PSO-based IT2F-PDC has lower overshoot, settling time, and control energy, but both have almost the same rise time. The proposed control strategy can be regarded as a promising strategy for controlling different unstable and nonlinear systems.
Municipal solid waste management (MSWM) poses a considerable challenge to developing countries like Bangladesh because of the rising waste generation rates and lack of effective management practices such as illegal open dumping and informal waste collection. One of the crucial factors in the successful management of MSW is to select the appropriate technology which is a complex multi-criteria and laborious process. Despite the global emphasis on the importance of MSWM in the literature, there is a lack of studies conducted in developing countries that effectively identify and analyze the critical performance criteria for appropriate technology selection. This research aims to address this shortcoming by identifying, and prioritizing the selection criteria and finally investigating the inter-relationship between them and the degree to which they affect or are affected by one another. First, a thorough literature review and expert consultation were employed to determine a set of 21 key criteria using the Fuzzy Delphi method (FDM). Later, taking into account the imprecise and subjective nature of the DEMATEL method on human judgements, the Fuzzy DEMATEL technique was employed to investigate the cause-effect relationships among the identified criteria. The findings of the study demonstrated that 14 criteria were categorized as causal elements that have the most significant influence on the MSWM technology selection process and 7 criteria were categorized as effect. The selection of MSWM technology demands greater consideration of the top three ranked criteria, namely T4- Access to Technology (AT), T8- Feasibility (F), and the Ec6-Infrastructure requirements (IR). By identifying the pertinent criteria, structures and interrelationships, the outcome of the study can facilitate a better understanding of causal relationships among the criteria that require specific consideration from the decision-makers and allow them to select appropriate MSW management technology.
In developing country like Malaysia, the demand for electricity is expected to rise with increasing urbanization and rapid industrialization. Currently energy production is mainly dependent on fossil fuel but in the near future fossil fuels will not be sustainable because of the depletion of existing reserves and their impact on the environment. Wave energy is an environmentally friendly and fastest growing renewable energy source for a sustainable electrical power generation of the future. Unlike others renewable energy resources, wave energy can produce electric power all over the year. As Malaysia has a total coastline of 4,675 kilometers so there is a great potential for utilization of wave energy in Malaysia especially along the coast and the islands. This paper presents a feasibility study of wave energy at different locations in Malaysia including the estimation of the total power available from the seas surroundings Malaysia. Furthermore, the analysis of investment, operation and maintenance cost for a wave farm is also presented.
19 November 2014 in Materials and Manufacturing Processes
Metallic powder and binder mixing mechanism plays a vital role in the quality of molded parts in metal injection molding. The present study is intended for experimental and theoretical investigation of powder–binder mixing mechanism to investigate the functional correlation among mixing parameters and performance characteristics for different composition of feedstocks. Powder loading and shear rate are considered as input parameter. Fuzzy expert system is adopted to test the validity of the experimental results by analyzing different numerical error criteria using the viscosity as output with respect to input parameters. The mean relative error and correlation coefficient for type A and type B were found to be 6.09% and 8.51% (<10%) and 0.990 and 0.998, respectively. Hence the result indicates a reliable acceptability of the proposed amount of powder loading for feedstock preparation.